Discounted Products

Dedicated crimp tool The JST Crimping Tools are parallel action, ratchet style hand tools designed to crimp the applicable contact in strip form, while maintaining the reliability and performance of semi-automating tooling. Features & Benefits • Ratchet mechanism for crimp conformation • Precision ground dies • Safe operation • 2 crimping sections Standards UL, CSA, TUV Dedicated crimp tooling (JST)

DLX Series Chassis Connectors All metal housing gives greater overall RF protection and shielding Duplex ground contact improves contact integrity between chassis and cable connector Warning Not to be used as mains connectors

Klaxon Sonos LED Base Sounder Beacon The Klaxon Sonos LED Base can accommodate various detector heads from major manufacturers. It reduces wiring and installation costs and provides both detection and alarm at the same point. With the addition of a cover plate, it can be used as a standalone sounder beacon. The Sonos LED base has twelve high powered LEDs and a 95 dB sounder and complies with the Disability and Discrimination Act (DDA). The beacon can be seen from every angle including directly below the unit. Features and Benefits Combined sounder beacon current consumption of less than 10 mA Unique beacon design for optimal light coverage Two large cable entries for quick and simple installation Designed to complement various detectors 32 distinct alarm tones Cover plate available for use as a sounder beacon only Applications The Sonos LED Base Sounder Beacon is an ideal solution for any type of fire alarm application. Standards EN54-3 Type A.

The SKF shims are made up of high quality stainless steel. It is easy to fit and remove. Fully de-burred Close tolerances for accurate alignment

CONN PLUG 4POS PANEL MOUNT

CAP CER 0.047UF 16V Y5V 0402

Sensor Head Fitted with a conical, UV stable, impact resistant, translucent cover Omni-directional NEMA connection Replacement for sensors using NEMA Rotaloc Socket Daylight Lighting Controllers These controllers automatically turn lights 'ON' and 'OFF' in response to changes in ambient light levels, primarily the transition from day to night and vice-versa. The more advanced types (see note below) have inbuilt logic to minimise false triggering, whereas the remainder have inbuilt time delays or higher 'OFF' thresholds, to prevent on/off cycling. As a general rule, these controllers should be sited such that they are not illuminated, by the light they are controlling. Nominal supply voltage is 230Vac.,Note regarding energy-saving negative-hysteresis controllers,Where figures for the 'OFF' threshold are lower than for the 'ON' threshold, the sensor is designed such that four thresholds are actually monitored. These are: dusk, the middle of the night, dawn and the middle of the day. Monitoring at times other than dusk and dawn enables the sensor to determine what it should be looking for next, minimising false triggering and improving overall controller operation.

POT 10K OHM 1/20W CARBON LINEAR

HF18FH Series Sockets HongFa professional range of din rail mount relay sockets for the HF18 series power relays.

320 WATTS VARIABLE 33 OHMS 10%

DGTL ISO 5KV RS422/RS485 16SOIC

LED DRIVER CC AC/DC 103-171V

TLS-GD2 Solenoid Interlock Switch, for Demanding Applications Features & Benefits Note The TLS-GD2 is a positive mode, tongue operated guard locking interlock switch that locks a machine guard closed until power is isolated and ensures that it remains isolated while the guard is open. The switch has three safety (N.C.) contacts and two auxiliary (N.O.) contacts. The head of this interlock switch has two entry slots and it can be rotated to provide four actuator entry points. A blanking plug is provided to seat the unused slot. The guard may only be opened when a signal is applied to the TLS-GD2 internal solenoid which releases the lock mechanism. Therefore this solenoid interlock switch is ideal for machines which do not stop immediately or where premature interruption of the machine could cause damage to tooling and components or cause an additional hazard. The safety switch is available in three types. The TLS-1 GD2 and TLS-3 GD2 incorporate a power-to-release function. Two manual release points with security screws allow the locked TLS-GD2 to be released in emergencies. An optional lid-mounted key-release style can also be supplied. The TLS-2 GD2 has a power-to-lock function. Each type of switch has five sets of contacts of various forms and are suitable for use with PLCs. The TLS-1 GD2 and TLS-3 GD2 are both available with escape release options. They are intended for machine guarding with full body access. The switch is installed so that the escape release push button on the rear side is accessible from inside the hazardous area. This allows the intentional unlocking of the TLS-GD2 from inside a hazardous area, providing a means of escape for a person who may become trapped. A stainless-steel actuator guide is fitted to protect the switch from actuator damage due to poor guard alignment or guard wear. TLS-GD2 has an ingress protection rating ...

DC/DC CONVERTER 5V 15W

Plastic Filter Units A 4mm filter gives 60% retention of dust particles (replacement filters 80 x 80mm 494-7975 & 120 x 120mm 494-7981 The finger guard is attached to the fan with screws (not supplied). The mesh screen and filter are then retained by the outer cover which clips over the finger guard Note Filter units ( 696-3534 , 696-3531 , 221-336 & 221-342 ) include filter pads. Filter pad replacements ( 494-7975 and 494-7981 ) are also available separately for filter units 221-336 & 221-342 .

STM32 DISCOVERY PACK LTE IOT

SENSOR REED SW SPST-NO W LEADS

BOARD EVAL LTC2954

CABLE ROLLER FOR CABLES UP TO 1"

Ehmann LED Flush Mounted Dimmer This Bodo Ehmann electronic LED dimmer switch is silent, as it operates without a choke. There is no standby consumption thanks to a real on/off switch saving energy. The minimum and maximum brightness can be adjusted in wide ranges, resulting in flickering free lighting of the luminaire at these levels, Features and Benefits Suitable for dimmable led lamps, LED driver for incandescent and HV-halogen lamps Wide range from minimum to maximum brightness No standby consumption, with on/off switch Silent operation Note These dimmers have been fully tested for use with led lamps. For a full compatibility list of LED Lamps, use the QR Code. Switches

EVO9 Series Cable Tie Tensioning Tools The EVO9 cable tie tensioning tool from HellermannTyton is ergonomically designed to reduce the risk of repetitive stress injuries to operators while concurrently increasing productivity. It tensions, locks and cuts the cable tie. The EV09 is available in a standard grip span (stock no.126-8893), short grip span (stock no.126-8894) and high tension (stock no.126-8895).Features and Benefits Ergonomic, slip-proof handle for a comfortable and secure gripLow maintenanceFast and precise application with minimum effort (TLC mechanism)Convenient and simple tension adjustmentIntegrated 3 position quick adjustment overrideHousing made of resilient and lightweight glass fibre reinforced polyesterStandard grip span (95 mm) and short grip span (90 mm) availableApplications The EVO9 cable tie tensioning tool can be used in the Aerospace, Automotive, Chemical, Defence, Electronics, Food, Offshore, Rail, Shipbuilding, Solar, Wind and Telecommunications industries.Approvals RoHS.

EC PCB Fan Speed Controllers Unboxed manual speed controllers for use with EBM-Papst EC (electronically commutated) fans. These are all purely the control assembly and PCB and are not mounted in an enclosure. CN1003 (743-4807) variable speed controller The CN1003 ( 743-4807 ) unboxed controller is designed for use with the full range of ebm-papst ECi (Electronically Commutated with integrated electronics) fans. It is powered via the DC output from by the fan and provides a 0-10V signal to enable infinitely variable speed control. The controller also enables speed measurement of the fan using a multimeter with a frequency measuring facility (where a tacho output is provided from the fan). Specification: Input voltage 10 VDC (supplied from fan); Maximum ambient temperature 50°C; Mounting hole diameter 10mm; Output voltage range 0-10 VDC. CN1064 (743-4810) 5 position speed controller The CN1064 ( 743-4810 ) unboxed 5 speed controller is designed for use with the full range of ebm-papst EC fans. Powered by the 10VDC output from the motor, it provides variable speed control with 5 speed settings. Each setting can be adjusted during commissioning between 0 % to 100% speed. This controller can control multiple fans running at the same speed. No separate power supply required. CN1063 (743-4817) adjustable max / min variable speed controller The CN1063 ( 743-4817 ) unboxed controller is designed for use with the full range of ebm-papst EC fans. Powered by the 10V DC output from the motor, it provides infinitely variable, manual speed control between 0% and 100%. However, the CN1063 ( 743-4817 ) differs from the CN1003 ( 743-4807 ) in that it has adjustable limits. The maximum and minimum speeds can be varied during commissioning to limit the maximum speed and/or restrict the lower speed. No separate power supply is required.

CWC Series Professional range of WEG contactors from the CWC Series designed for switching of electric motors. The contactors are modular and compact but at the same time robust and highly reliable. Built and tested according to IEC/EN60947 and DIN VDE 0660. Direct mounting capabilities. The controllers include contactors and reversing contactors. AC/DC Operated Screw Terminals DIN Rail or Panel Mount Compact space saving design Built in auxiliary contacts WEG Contactors

FIBOX Euronord Aluminium Enclosure Euronord range of enclosures from Fibox are designed to house DIN Rail-mounted terminal blocks and various types of sensors. The enclosure lid has a sealing gasket, and can be easily sealed with a single 90° turn on the quick-lock stainless steel screw. Features and Benefits • Temperature range -50°C to +80°C (continuous), -50 to +140°C (short term) • Designed to house DIN Rail-mounted terminal blocks and various types of sensors • IP 66/67 • Base colour RAL 7001 (IP) Ingress Protection and what it means? IP rating classifies the degrees of protection provided against the intrusion of solid objects (including body parts like hands and fingers), dust, accidental contact, and water in electrical enclosures. FAQ’s Can the box be used outside? • Yes, Euronord series enclosures have IP66, IP67 & IP68 rating Can you purchase mounting plates separately • No, Euronord mounting plates are not available separately What is supplied? • Enclosure, Base with screws for mounting plate/ DIN Rail, cover with PUR or Neoprene gasket and stainless steel cover screws Standards EN 62208:2003 (50298:1998). EN 60950. Approvals UL Type 1, 4, 4X, 12, 13 (USA); IP 67/IP 66 (EURO); IEC 529 (Others)