Rates
1+
£ 486.90
Products Found: 372
Showing Results For: Signal Conditioners
Signal Conditioners
FILTERS
Filters
Showing
1 -
New Items
New items
5131AA, PR Electronics
5131A - 2-wire Programmable Transmitter
The 5131A is a 2-wire programmable transmitter. The transmitter is for conversion of linear resistance variation to a standard analog current / voltage signal, for example from solenoids and butterfly valves or linear movements with attached potentiometer.
This transmitter can be configured with the software program PReset using a standard PC and the Loop Link communications unit (stock-no.
796-7020
).
2-wire programmable transmitter
1-channel, stock-no.
827-5491
2-channel, stock-no.
796-6893
Input for RTD, TC, mV, linear resistance, mA, and V sample
Linearized, electronic temperature measurement with RTD or TC sensor
4- or 3-wire connection automatic cable compensation or 2-wire connection with programmable cable compensation
Current input programmable in range 0-100 mA and voltage inputs in range 0-250 Vdc
4-20 mA loop output, can be configured to any current within 0-20 mA range
Voltage output range is selectable between 0-10 Vdc
Independent channel jumper selectable inputs for current/voltage or temperature
Programming can be performed with or without a power supply
3.75 kVac galvanic isolation between the channels
Configurable sensor error detection including NAMUR NE43
DIN rail mounting
Temperature Transmitters
4 to 20mA loop powered output and reverse polarity protection, configurable without the need for a PC or software
New items
MTL5546Y, Eaton
Intrinsic Safety Interface Units - Eaton MTL 5500 Series
Features and Benefits
New items
PXT-10.924/RS, Brodersen Controls
Temperature Converter
Galvanic isolation output to supply
Pt100 2 or 3-wire operation
Selectable input sensor temperature range: -50 to +100°C or -50 to +300°C
Output selectable via terminals: 0 to 10V, 0 to 20mA or 4 to 20mA
Offset and gain adjustable via front panel, ±5% of max signal
Note
Pt100 sensor not supplied
Brodersen DIN Rail Mounting
NORYL housing
Dimensions: H80 x W22.5 x D104mm
Operating temperature range: -20 to +55°C
New items
GN21000S, GEORGIN
The SG family of signal conditioners have been developed to provide users with high reliability, space savings and significant savings in installation and maintenance.
Isolation amplifier, separator, signal repeater, transmitter power supply, temperature transmitter are all available functions guaranteeing ease of use and remarkable performance.
Our industry-unique factory calibration method delivers exceptional response time and precision.
Function: Signal splitter - 1 Channel
Input (I): Active: 0/4 to 20mA (=35Ohm) 16V@20mA
Input (V): 0/2 to 10V, 0/1 to 5V (=100kOhm)
Output (I): Active: 0/4 to 20mA (=300Ohm@20mA)
Output (V): 0/2 to 10V, 0/1 to 5V (=2KOhm@10V)
Power supply: 16.8V to 31.2Vdc
New items
6185D, PR Electronics
6185 Type - Loop-powered Isolator
6185 type is a 1-, 2- or 4-channel galvanic isolation module. Inputs and outputs are floating and galvanically separated. Elimination of ground loops and measurement of floating signals. Especially useful in applications necessitating an unproblematic transmission of current signals according to NAMUR (sensor error detection).
Loop-powered isolator
1-channel version, stock-no.
796-6991
2-channel version, stock-no.
796-6916
4-channel version, stock-no.
796-6948
No separate supply necessary
Low response time
High noise suppression
Powered by the measured signal and loads the loop with max. 1.8 Vdc
Input is protected against overvoltage and polarity error
Drop voltage for each channel can be calculated according to the following expression: V
drop
= 1.8 + (I
out
* R
load
) Output is voltage-limited to 15 Vdc
DIN rail mounting
PR Electronics DIN Rail Mounting
New items
3225A, PR Electronics
The PR Electronics Universal Frequency Converter units can be mounted side by side, horizontally and vertically, without air gap on a standard DIN rail, even at 70°C ambient temperature. All programming can be password protected. All terminals are over-voltage protected, polarity protected and short-circuit protected. The device is provided with field wiring terminals and shall be supplied from a power supply having double / reinforced. Insulation. a power switch should be easily accessible and close to the device. the power switch shall be marked as the disconnecting unit for the device.
2.5 kvac isolation
Power supply 16.8 vdc,31.2 vdc
Buffered voltage output 10 vdc
Measures frequencies up to 100 kHz
New items
3114, PR Electronics
3100 Type - Isolated Converter
3104, 3109 and 3114 type are for isolation and conversion of standard DC signals.
Suitable for galvanic separation of analog DC signals and elimination of ground loops and measurement of floating signals.
Conversion of standard DC signals
Slimline housing of 6 mm
Power supply and signal isolator for 2-wire transmitter
Loop supply >17 V
DIP-switch configured
Inputs and outputs are floating and galvanically separated
Isolation 2.5 mm
Installation in ATEX Ex zone 2 / IECEx zone 2 / FM division 2
PR Electronics DIN Rail Mounting
New items
New items
MTL5549Y, MTL
5500 Series IS Interface Units
The MTL5500 series is the latest generation of MTL isolators. Incorporating advanced circuit design and innovative isolating transformer construction. The compact 16mm wide design reduces weight and gives a high packing density and reduction in power consumption. They build on the success of the MTL5000 series to bring the benefits of galvanic isolation with exceptional design and reliability.,II (I) GD (Ex ia) IIC,IECEx, ATEX (Baseefa) FM, CSA
3-Port Isolation
High Packing density
Low power dissipation
Multi-channel I/O modules
Compatible with preceding MTL5000 series
Assessed for Functional safety IEC61508 applications
Required EX numbers and information displayed on cover where applicable
New items
2261, PR Electronics
2261 Type - mV Transmitter The 2261 mV Transmitter converts bipolar mV signals from transducers supplied directly by the device to standard current / voltage signals.The device is also suitable for load cell application as well as other applications such as tank filling and draining, weighing with a taring function, measurement of cable tensile force, level control, signal conversion / amplification etc. Load cell amplifiermV to current / voltage conversionFront-programmableLED displayFront error LEDRelative calibration of input spanNPN / PNP input for external taringSupply for standard transducersPR Electronics DIN Rail Mounting
New items
New items
