Rates
1+
£ 325.71
Products Found: 373
Showing Results For: Signal Conditioners
Signal Conditioners
FILTERS
Filters
Showing
1 -
New Items
New items
MTL5546Y, Eaton
Intrinsic Safety Interface Units - Eaton MTL 5500 Series
Features and Benefits
New items
3225A, PR Electronics
The PR Electronics Universal Frequency Converter units can be mounted side by side, horizontally and vertically, without air gap on a standard DIN rail, even at 70°C ambient temperature. All programming can be password protected. All terminals are over-voltage protected, polarity protected and short-circuit protected. The device is provided with field wiring terminals and shall be supplied from a power supply having double / reinforced. Insulation. a power switch should be easily accessible and close to the device. the power switch shall be marked as the disconnecting unit for the device.
2.5 kvac isolation
Power supply 16.8 vdc,31.2 vdc
Buffered voltage output 10 vdc
Measures frequencies up to 100 kHz
New items
8.SK.1A-1S1D2RS, Kübler
The SK 1A-1S1D2RS is a universal converter for analog input signals from ±10 V or 0/4 ... 20 mA. This module converts analog signals in a digital format (frequency, position or angular position). The output format can be an incremental signal or an absolute value in SSI format. In addition, the result of the conversion can be read via a serial RS232 or RS485 interface or via a USB port. The module can be easily and conveniently mounted in a cabinet on a standard DIN rail.
Motor potentiometer function.
Analog input suitable for voltage, current or potentiometer operation.
Output operating modes: frequency generator, motor potentiometer, position or angle sensor or measurement data acquisition.
Programmable characteristic U/f curve and possibility of generating repetitive frequency sweeps.
Frequency output (HTL or TTL, max. 1 MHz) proportional to the input signal.
Incremental encoder output and SSI interface for displaying a position or an angular position.
Incremental direction information A, B depending on the input signal and on the programmed conversion range.
USB programming interface and serial interface (RS232 / RS485).
Programmable zero pulse (0, /0).
New items
PXT-10.924/RS, Brodersen Controls
Temperature Converter
Galvanic isolation output to supply
Pt100 2 or 3-wire operation
Selectable input sensor temperature range: -50 to +100°C or -50 to +300°C
Output selectable via terminals: 0 to 10V, 0 to 20mA or 4 to 20mA
Offset and gain adjustable via front panel, ±5% of max signal
Note
Pt100 sensor not supplied
Brodersen DIN Rail Mounting
NORYL housing
Dimensions: H80 x W22.5 x D104mm
Operating temperature range: -20 to +55°C
New items
New items
ICM40030, Red Lion
ICM4 - Interface converter, RS232 to RS485/RS422
Converts from RS232 to RS485/RS422 and vice versa
3 INFO LEDs for RXD, TXD and power supply
Easy to mount onto DIN rail
Max. Cable length:
RS232: 15 m, RS485: 1200 m
RS485:
Up to 32 RS485 receivers can be
connected in parallel
Baud rate:
min. 9600 Baud, max. 19200 Baud
Power supply:
9 → 32 VDC max. 75 mA
Ambient temp.:
Operation:
0 °C → +50 °C
Bearings:
40 °C → +75 °C 85% rel. air humidity
Housing:
stable plastic housing
Dimensions (WxHxD):
25 x 98 x 79 mm
New items
New items
GT45000S, GEORGIN
The SG family of signal conditioners have been developed to provide users with high reliability, space savings and significant savings in installation and maintenance.
Isolation amplifier, separator, signal repeater, transmitter power supply, temperature transmitter are all available functions guaranteeing ease of use and remarkable performance.
Our industry-unique factory calibration method delivers exceptional response time and precision.
Function: Universal input converter - 1 Channel
Input: Rtd100 2/3/4 wires, RTD1000, Ni100, Ni1000, TC
KTY, Res. 0 to 5000Ohm Pot.100Ohm to 50kOhm
Output (I): Active: 0/4 to 20mA, 0/2 to 10mA (=600Ohm@20mA)
Output (V): 0/2 to 10V, 0/1 to 5V (=2KOhm@10V)
Po
New items
2902019, Phoenix Contact
3-way signal conditioner, with configurable input/output, for electrical isolation and conversion of analog signals in the mV and V range, unipolar as well as bipolar. Screw connection technology, standard configuration.
New items
New items
1050201, Phoenix Contact
Temperature transducer, converts signals from resistance temperature detectors and resistors into analog 0/4 - 20 mA signals. Freely programmable, Push-in connection, 3-way electrical isolation, standard configuration.
New items
5131AA, PR Electronics
5131A - 2-wire Programmable Transmitter
The 5131A is a 2-wire programmable transmitter. The transmitter is for conversion of linear resistance variation to a standard analog current / voltage signal, for example from solenoids and butterfly valves or linear movements with attached potentiometer.
This transmitter can be configured with the software program PReset using a standard PC and the Loop Link communications unit (stock-no.
796-7020
).
2-wire programmable transmitter
1-channel, stock-no.
827-5491
2-channel, stock-no.
796-6893
Input for RTD, TC, mV, linear resistance, mA, and V sample
Linearized, electronic temperature measurement with RTD or TC sensor
4- or 3-wire connection automatic cable compensation or 2-wire connection with programmable cable compensation
Current input programmable in range 0-100 mA and voltage inputs in range 0-250 Vdc
4-20 mA loop output, can be configured to any current within 0-20 mA range
Voltage output range is selectable between 0-10 Vdc
Independent channel jumper selectable inputs for current/voltage or temperature
Programming can be performed with or without a power supply
3.75 kVac galvanic isolation between the channels
Configurable sensor error detection including NAMUR NE43
DIN rail mounting
Temperature Transmitters
4 to 20mA loop powered output and reverse polarity protection, configurable without the need for a PC or software