Rates
1+
£ 357.03
Products Found: 373
Showing Results For: Signal Conditioners
Signal Conditioners
FILTERS
Filters
Showing
1 -
New Items
New items
3225A, PR Electronics
The PR Electronics Universal Frequency Converter units can be mounted side by side, horizontally and vertically, without air gap on a standard DIN rail, even at 70°C ambient temperature. All programming can be password protected. All terminals are over-voltage protected, polarity protected and short-circuit protected. The device is provided with field wiring terminals and shall be supplied from a power supply having double / reinforced. Insulation. a power switch should be easily accessible and close to the device. the power switch shall be marked as the disconnecting unit for the device.
2.5 kvac isolation
Power supply 16.8 vdc,31.2 vdc
Buffered voltage output 10 vdc
Measures frequencies up to 100 kHz
New items
8.SK.1A-1S1D2RS, Kübler
The SK 1A-1S1D2RS is a universal converter for analog input signals from ±10 V or 0/4 ... 20 mA. This module converts analog signals in a digital format (frequency, position or angular position). The output format can be an incremental signal or an absolute value in SSI format. In addition, the result of the conversion can be read via a serial RS232 or RS485 interface or via a USB port. The module can be easily and conveniently mounted in a cabinet on a standard DIN rail.
Motor potentiometer function.
Analog input suitable for voltage, current or potentiometer operation.
Output operating modes: frequency generator, motor potentiometer, position or angle sensor or measurement data acquisition.
Programmable characteristic U/f curve and possibility of generating repetitive frequency sweeps.
Frequency output (HTL or TTL, max. 1 MHz) proportional to the input signal.
Incremental encoder output and SSI interface for displaying a position or an angular position.
Incremental direction information A, B depending on the input signal and on the programmed conversion range.
USB programming interface and serial interface (RS232 / RS485).
Programmable zero pulse (0, /0).
New items
New items
ICM40030, Red Lion
ICM4 - Interface converter, RS232 to RS485/RS422
Converts from RS232 to RS485/RS422 and vice versa
3 INFO LEDs for RXD, TXD and power supply
Easy to mount onto DIN rail
Max. Cable length:
RS232: 15 m, RS485: 1200 m
RS485:
Up to 32 RS485 receivers can be
connected in parallel
Baud rate:
min. 9600 Baud, max. 19200 Baud
Power supply:
9 → 32 VDC max. 75 mA
Ambient temp.:
Operation:
0 °C → +50 °C
Bearings:
40 °C → +75 °C 85% rel. air humidity
Housing:
stable plastic housing
Dimensions (WxHxD):
25 x 98 x 79 mm
New items
New items
GT45000S, GEORGIN
The SG family of signal conditioners have been developed to provide users with high reliability, space savings and significant savings in installation and maintenance.
Isolation amplifier, separator, signal repeater, transmitter power supply, temperature transmitter are all available functions guaranteeing ease of use and remarkable performance.
Our industry-unique factory calibration method delivers exceptional response time and precision.
Function: Universal input converter - 1 Channel
Input: Rtd100 2/3/4 wires, RTD1000, Ni100, Ni1000, TC
KTY, Res. 0 to 5000Ohm Pot.100Ohm to 50kOhm
Output (I): Active: 0/4 to 20mA, 0/2 to 10mA (=600Ohm@20mA)
Output (V): 0/2 to 10V, 0/1 to 5V (=2KOhm@10V)
Po
New items
2902019, Phoenix Contact
3-way signal conditioner, with configurable input/output, for electrical isolation and conversion of analog signals in the mV and V range, unipolar as well as bipolar. Screw connection technology, standard configuration.
New items
New items
1050201, Phoenix Contact
Temperature transducer, converts signals from resistance temperature detectors and resistors into analog 0/4 - 20 mA signals. Freely programmable, Push-in connection, 3-way electrical isolation, standard configuration.
New items
3114, PR Electronics
3100 Type - Isolated Converter
3104, 3109 and 3114 type are for isolation and conversion of standard DC signals.
Suitable for galvanic separation of analog DC signals and elimination of ground loops and measurement of floating signals.
Conversion of standard DC signals
Slimline housing of 6 mm
Power supply and signal isolator for 2-wire transmitter
Loop supply >17 V
DIP-switch configured
Inputs and outputs are floating and galvanically separated
Isolation 2.5 mm
Installation in ATEX Ex zone 2 / IECEx zone 2 / FM division 2
PR Electronics DIN Rail Mounting
New items
New items
