Rates
1+
£ 57.47
Products Found: 337
Showing Results For: Pneumatic Sensor & Switch Accessories
Pneumatic Sensor & Switch Accessories
FILTERS
Filters
Showing
1 -
New Items
New items
0860000000000000, IMI Norgren
The IMI Norgren 51D Mountings. Port size is G1/8. Switching status indicated by LED, versions with analogue output signal on request.
High accuracy and resolution
Switching status indicated by LED
Versions with analogue output signal on request
New items
NEBU-M8G3-E-10-LE3, Festo
The Festo's NEBU series 3-pin, M8 connecting cable has a length of 10m. This device is enabled with a standard, straight cable outlet for a plug socket. It is suitable for use with energy chains and robot application. The product weight is 242g
Ambient temperature -25 to 80 °C
Free of copper and PTFE
New items
KMV-1-24DC-5-LED, Festo
The Festo's plug socket with cable which is pre-assembled and used for V solenoid Its mount on solenoid valve with M3 central screw. Its cable length is 5mm
Protection class IP67
Ambient temperature -20 to 80 °C
New items
NEBU-M8G3-R-10-LE3, Festo
The Festo's NEBU series 3-pin, M8 connecting cable has a length of 10m. This device is enabled with a standard, straight cable outlet for a plug socket. It is suitable for use with energy chains and robot application. The product weight is 242g and its ca
Ambient temperature -25 to 70 °C
Free of copper and PTFE
New items
BMY3-016, SMC
Rail Mounting.
For CDQ2, CDQP2, CDBQ2, CDLQ, CDQ2X, CDQ2Y, CDQM, RDQ, RDLQ, C55, NCQ8, RZQ, CXT, MK, MK2, RSDQ, MDU, MDLU, CE1.
For MHF2, MHZ2, MHZJ2, MHZL2, MHL2, MDHR2, MDHR3, MHK2, MHS2, MHS3, MHSJ3, MHSH3, MHSL3, MHS4, MHC2, MHT2, MHY2, MHW2, MRHQ
New items
NEBV-S1WA44-K-2.5-N-LE44-S9, Festo
Festo NEBV Series Connecting Cables
Festo NEBV series connecting cables for the VUVG series valves. The NEBV series pre-assembled leads have a 2-pin straight socket connection and a grey PVC cable available in a variety of lengths.
Conversion Table
Conversion
Factor
Bar to mmHg
750.06
Bar to PSI
14.50
Bar to kPa
100
New items
KMYZ-2-24-M8-2,5-LED, Festo
The Festo KMYZ series pre-assembled connecting cable has a 2.5m cable length with 2-pin M8 plug socket connection . This cable is suitable for V solenoids with M3 central screw in any assembly position . It has nominal operating voltage of 24 VDC.
Switching position indicator - LED
Electrical connection - plug socket
Product weight - 170 g
New items
NEBC-D12G4-ES-3-S-D12G4-ET, Festo
Festo NEBC Series Connecting Cables
The Festo NEBC series connecting cables are for connecting a CMMS-ST motor controller to any control system.
Features and Benefits
Connecting cable M12 4-pin
D-coded
Suitable for Ethernet
Suitable for use with energy chains
Cable Lengths:
1367079 - 1 m
1367080 - 3 m
1367081 - 5 m
1367082 - 10 m
1367083 - 1 m
1367084 - 3 m
1367085 - 5 m
1367086 - 10 m
Conversion Table
Conversion
Factor
Bar to mmHg
750.06
Bar to PSI
14.50
Bar to kPa
100
New items
GERMF-06, Igus
Clevis Joint and Clip
Igumid G clevis joint complete with spring clip
No corrosion and totally maintenance-free
May be combined with Igubal E Series rod ends
Low weight
Ideal for use with pneumatic cylinders and linkages
Rod End & Spherical - Maintenance Free IGUS®
IGUBAL® spherical bearings are self-lubricating, designed to run dry and are maintenance free
The bearings are extremely tolerant to dirt and dust - IGUBAL® can be used in abrasive environments
8 to 20mm bore size
Low weight (20% of equivalent steel)
High rigidity
Corrosion and chemically resistant
High fatigue strength under changing loads
Working temperature range: -30°C to +80°C
New items
P211080-1, SMC
Autoswitch
Vane Types 10-80mm Diameter
A range of compact, lightweight rotary actuators, ideal for turning small loads in confined spaces.
New items
BMF 305-HW-17, BALLUFF
Starter solenoid switch BMF 305K
Electronic switch
Bounce-free switching, no multiple switch points
M8 and M12 plug connectors
Automotive approved
Protection class IP67
Operating voltage 10 → 30 Vdc
3-cable, PNP, NO
Solenoid switch for pneumatic cylinders. "One for all": These sensors let you identify the piston position of pneumatic cylinders through the cylinder wall. Wear and contact-free. Holding brackets / slot nuts available for all commonly available cylinders. Reduced storage - only 1 sensor for different cylinders.
Balluff part no.
Cable
Plug connector
BMF 305K-PS-C-2-S49-00, 2
0.2 m PUR
M8
BMF 305K-PS-C-2-S4-00, 5
0.5 m PUR
M12
Balluff order ref.
Piston Ø of cylinder
Hose clamp size
BMF hose clamp size 1
8 → 16
1
BMF hose clamp size 2
20, 25
2
BMF hose clamp size 3
32
3
Usability
Holding bracket / slot nut for adapting the BMF 305 to different cylinders (see accompanying drawings)
BMF 305-HW-20
For T-slot cylinders as per drawing. Even when you replace the sensor, the switch is captively fixed with the holding bracket
BMF 305-HW-17
For T-slot cylinders, e.g. Festo, SMC, installed from above. Even when you replace the sensor, the switch is captively fixed with the holding bracket.
BMF 305-HW-23
For T-slot cylinders as per drawing. Installed from above. Even when you replace the sensor, the switch is captively fixed with the holding bracket.
BMF 305-HW-26
For SMC T-slot A or T-slot B cylinders. Holding bracket for slot A installed from above. Even when you replace the sensor, the switch is captively fixed with the holding bracket.
BMF 305-HW-24
Terminal part for round cylinders with piston diameter of 8 → 80 mm, not including slot. A hose clamp the size of the cylinder is also required for mounting (see table). Even when you replace the sensor, the switch is captively fixed.
New items
BMF 305-HW-20, BALLUFF
Starter solenoid switch BMF 305K
Electronic switch
Bounce-free switching, no multiple switch points
M8 and M12 plug connectors
Automotive approved
Protection class IP67
Operating voltage 10 → 30 Vdc
3-cable, PNP, NO
Solenoid switch for pneumatic cylinders. "One for all": These sensors let you identify the piston position of pneumatic cylinders through the cylinder wall. Wear and contact-free. Holding brackets / slot nuts available for all commonly available cylinders. Reduced storage - only 1 sensor for different cylinders.
Balluff part no.
Cable
Plug connector
BMF 305K-PS-C-2-S49-00, 2
0.2 m PUR
M8
BMF 305K-PS-C-2-S4-00, 5
0.5 m PUR
M12
Balluff order ref.
Piston Ø of cylinder
Hose clamp size
BMF hose clamp size 1
8 → 16
1
BMF hose clamp size 2
20, 25
2
BMF hose clamp size 3
32
3
Usability
Holding bracket / slot nut for adapting the BMF 305 to different cylinders (see accompanying drawings)
BMF 305-HW-20
For T-slot cylinders as per drawing. Even when you replace the sensor, the switch is captively fixed with the holding bracket
BMF 305-HW-17
For T-slot cylinders, e.g. Festo, SMC, installed from above. Even when you replace the sensor, the switch is captively fixed with the holding bracket.
BMF 305-HW-23
For T-slot cylinders as per drawing. Installed from above. Even when you replace the sensor, the switch is captively fixed with the holding bracket.
BMF 305-HW-26
For SMC T-slot A or T-slot B cylinders. Holding bracket for slot A installed from above. Even when you replace the sensor, the switch is captively fixed with the holding bracket.
BMF 305-HW-24
Terminal part for round cylinders with piston diameter of 8 → 80 mm, not including slot. A hose clamp the size of the cylinder is also required for mounting (see table). Even when you replace the sensor, the switch is captively fixed.