Rates
1+
£ 6.21
Products Found: 882
Showing Results For: Threading Taps
Threading Taps
FILTERS
Filters
Showing
1 -
New Items
New items
4405926, EXACT
SGE-Bit HSS TIN Combi Tool
Combined HSS TIN single-cut tap with spiral flute and 1/4" hex drive
Deburring zone with edge breaker
For core drilling, thread cutting and deburring in a single process
Crosswise grinding, drills do not drill off-centre — even without centre-punching
Suitable for construction steel, CrNi steel, non-ferrous metals and plastics
New items
00031, EVENTUS
ISO HSS Metric (Coarse) Spiral Point Ground Taps
Precision HSS taps for machine tapping
Can be used for hand tapping without need of a lead tap.
Designed with a straight flute supplemented by an angular cutting point leaves the flutes clear of swarf for free coolant flow.
Blue steam tempered finish reduces friction and produces a fine finish thread
New items
10703, EVENTUS
Manual tap sets, 3-part, metric assortment
HSS manual tap assortments with straight flute, profile ground and relief ground
3-piece sets of all sizes, each with 1 x front, middle and bottom tap
For metric ISO thread DIN 13, tolerance 6H
Square stem
Tap wrench separate, see RS stock no.
508-9389
ff.
Suitable for construction steel, CrNi steel, non-ferrous metals and plastics
Includes
Assortment, 21 parts
1 set each of taps M3, M4, M5, M6, M8, M10 and M12
Supplied in a steel cassette case
Assortment, 29 parts
1 x each drill 2.5; 3.3; 4.2; 5; 6.8; 8.5 and 10.2 mm
1 set each of taps M3, M4, M5, M6, M8, M10 and M12
Supplied in a steel cassette case
Standards
DIN 352
New items
10306, EVENTUS
Machine Tap, Straight Flute, Through Holes
HSS-G machine tap with straight flute, profile ground and relief ground
For metric ISO thread DIN 13, tolerance 6H
B format, with 5-pitch spiral point, for through holes
Reinforced, M12 with fall-through shaft
Standards
DIN 371, DIN 376
New items
227.S4X70T2, Facom
The Facom 227 series is the high performance cobalt tap. The hardness of cobalt increases torque resistance and wear compared with standard taps. The size of the cobalt tap is the 4 mm.
Molybdenum and cobalt steel
Weight is the 10 g
New items
E100 2N8, Dormer
Set of three E100 metric pitch HSS hand tap bits
Set of metric pitch HSS hand tap bits offered in a set of 3 parts (taper, intermediate and finishing tap bits).
Each set consists of a taper tap bit with an I/P of 5 threads; the intermediate has an I/P of 3.5 threads and the finishing model has an I/P of 2 threads.
The tap bit tolerance class is 6H, the cutting angle is 10° and the tap flutes are straight.
These high-quality tap bits are ideal for tapping in blind or through-holes.
Standard: DIN 352
New items
E003M4, Dormer
Spiral Flute
Specially formulated high helix of 48º allows adequate room for chip formation and rapid and smooth chip evacuation at high cutting speeds for threading blind holes of up to 2.5 x diameter of the tap used. The 3 radii flute profile gives a constant rake angle all along the flute length, while the short thread length means low torque and better chip evacuation.
MTTX-HSS Taps
MTT-X taps are manufactured from premium quality vanadium powder steel, branded HSS-XS1, for an unbeatable combination of toughness, edge strength and wear resistance. This winning combination enables them to withstand the stresses of threading in tough materials.
New items
E003M6, Dormer
Spiral Flute
Specially formulated high helix of 48º allows adequate room for chip formation and rapid and smooth chip evacuation at high cutting speeds for threading blind holes of up to 2.5 x diameter of the tap used. The 3 radii flute profile gives a constant rake angle all along the flute length, while the short thread length means low torque and better chip evacuation.
MTTX-HSS Taps
MTT-X taps are manufactured from premium quality vanadium powder steel, branded HSS-XS1, for an unbeatable combination of toughness, edge strength and wear resistance. This winning combination enables them to withstand the stresses of threading in tough materials.
New items
47126, Recoil
Metric STI Bottoming / Finishing Taps
Note
Size stated is the size of the relevant insert and not the size of the tap.
New items
E100 9N8, Dormer
Set of three E100 metric pitch HSS hand tap bits
Set of metric pitch HSS hand tap bits offered in a set of 3 parts (taper, intermediate and finishing tap bits).
Each set consists of a taper tap bit with an I/P of 5 threads; the intermediate has an I/P of 3.5 threads and the finishing model has an I/P of 2 threads.
The tap bit tolerance class is 6H, the cutting angle is 10° and the tap flutes are straight.
These high-quality tap bits are ideal for tapping in blind or through-holes.
Standard: DIN 352
New items
E294M5, Dormer
Dormer HSS-E TiN Coarse Fluteless Tap (E294)
High Speed Cobalt fluteless forming tap with Titanium Nitride coating specifically designed for use in floating tool holders and CNC machines.
Oil grooves to control the flow of coolant to the working area
High performance in a wide range of materials
Hig accuracy of cut and smoother surface finish than standard taps
Chip free operation resulting in a stronger, more resistant thread
DIN 2174
Fluteless Taps
New items
E002M2.5, Dormer
MTTX Spiral Flute Metric Coarse Machine Tap (E002)
For machining Metric Coarse threads in blind holes in most materials
Manufactured from premium grade powder metallurgy Steel
Increased Vanadium content
Capable of out-performing traditional HSS machine taps by up to 300%
Bright finish
Standards
Manufactured to ISO529 standards.
Special Application Taps - Dormer Vanguard
Designed with special cutting geometries and surface treatments to tap quickly and accurately in a specific range of engineering materials.
Coloured ring for quick identification of use
Made to ISO standards (tolerance Class 2 for 6H fit)
Selection Guide
Material type
Hardness (HB)
Blue
Yellow
White
Green
Black
Non-alloy steel
●
Stainless steel
●
Cast Iron
●
Titanium, pure
●
Titanium, alloyed
●
Nickel, pure
●
Copper & Brass
●
Brass & Bronze
●
Aluminium alloy, Si
●
Aluminium alloy, Si>10%
●
Thermoplastics
-
●
●