Discounted Products

BSP Reducers Reducing thread adaptors with male (Rs) BSP parallel thread to female (Rp) BSP parallel thread. Male thread is sealed at the port connection with a nitrile rubber seal. Operating temperature range without pressure reductions is -30 to +100°C. Manufactured from steel to BS5200 with a zinc yellow chromated finish to give a high corrosion resistance (500 hours in salt spray test). The 60° female cone makes these adaptors an ideal port fitting for use with our range of BSP reusable fittings and crimped hose assemblies. Features and Benefits Visible bite of progressive ring helps prevent blow-off Excellent sealing capacity when used in various applications including vacuum and hydraulic systems Stress evenly distributed throughout out minimising concentration at the bite point Compact overall dimensions make EO fittings ideal or confined spaces Note For adaptors of unequal sizes then the lower pressure rating is applicable. Standards DIN 3852 Warning Hydraulic systems can work at high pressures, and fittings and adaptors can be subjected to extreme loadings such as vibration and uncontrolled pressure peaks. When choosing fittings or adaptors careful attention should be given to the technical specifications.

CONN PLUG MALE 3POS SOLDER CUP

Polyamide Enclosure IP65 Small control enclosures of polyamide and reinforced with 30% glassbead Available with or without cable glands RAL 7035 Recessed area for membrane keypads Approvals 8888

Si1141/42/43 Proximity/Ambient Light Sensor Modules The Silicon Labs Si1141/42/43 combines an active optical reflectance proximity detector with an ambient light sensor and an infrared LED into a single 10-Pin QFN package. Their dual port operation enables reliable proximity detection for moving as well as stationary objects. The Si1141 has 1 LED driver with an Integrated IR LED - RS 8920016. The Si1142 has 2 LED drivers with and integrated IR LED - RS 8920025. The Si1143 has 3 LED drivers with and integrated IR LED - RS 8920028. With the Si1143, locate three infrared LEDs in an L-shaped configuration to enable triangulation of an object and in turn, via host software, creating a gesture based user interface. These modules have photodiodes which can be used to measure both visible and infrared light. Detect levels as low as 6 lux. - Adjustable proximity detection from 1 cm to over 50 cm - Up to 3 independent LED drivers - 15 current settings from 5.6 mA to 360 mA per driver - 25.6 μs LED driver pulse width - High EMI immunity without shielded packaging - Low power consumption Sensor Interfaces, Silicon Laboratories

Cyclon 6V Monobloc Cells 6V Cyclon monoblocs available in 2.5Ah, 5.0Ah and 8.0Ah capacities. Each offers 10 years float life and 2 years storage life Up to 2000 life cycles The monoblocs have the same characteristics as the individual Cyclon cells and approved to the UL924 specification Stock no Maximum Discharge 265-1953 14.3 A (5 min.); 8.1 A (10 min.) 5.9 A (15 min.); 3.4 A (30 min.) 1.9 A (60 min.); 1.4 A (90 min.) 0.48 A (5 hrs.); 0.32 A (8 hrs.) 0.26 A (10 hrs.); 0.13 A (20 hrs.) 265-1969 28.9 A (5 min.); 18.1 A (10 min.) 13.5 A (15 min.); 7.1 A (30 min.) 4.0 A (60 min.); 2.8 A (90 min.) 1.0 A (5 hrs.); 0.61 A (8 hrs.) 0.52 A (10 hrs.); 0.26 A (10 hrs.) 265-1975 41.7 A (5 min.); 26.4 A (10 min.) 19.0 A (15 min.); 11.0 A (30 min.) 6.2 A (60 min.); 4.4 A (90 min.) 1.6 A (5 hrs.); 1.0 A (8 hrs.) 0.81 A (10 hrs.); 0.42 A (10 hrs.) Warning Do not charge in a sealed enclosure.

DIN 41622 Double Row Connectors 8,12,16,20 and 30 ways available Male and Female variants

CAP ALUM 10UF 20% 50V RADIAL

IP66 Terminal Enclosure IP66 Simple wall mounting All-welded basic body High IP index achieved by all-round knife edges against which an expanded PU seal is pressed 2.6mm gauge steel wall brackets RAL 7032 1.4mm wall thickness Note Not supplied with flange, DIN rail or chassis plates Sorry Your request could not be completed at this time

22 mm Push Button Heads, Plastic Siemens extremely rugged IP69K high-grade plastic push button heads. Avaliable in a variety of colours, illuminated, non-illuminated or mushroom style. Self-holding function of the actuator when mounting Twist prevention integrated into patented holder design Stackable contact modules Suitable for use in extreme environments No special tools required Simple geometry for mounting holes Latching or Momentary available Standards IEC 60947-1, EN 60947-1 IEC 60947-5-1, EN 60947-5-1 Siemens Sirius Act Range The SIRIUS ACT range of push buttons and signalling devices presents an expertly designed selection of push buttons, pilot lights and switches that are intelligent, reliable and physically robust. An innovative snap-on concept makes the task of installing a unit so effortless that it can be done with one hand. Made with real metals and high-grade plastics, installed with smart functions and interaction abilities, these state-of-the-art push buttons, indicator lights and switches have been extreme element tested to guarantee a long usage life and reliability for all your operations. One-handed installation without special tools Components can be snapped on without having to hold the other side Installation possible in a slanted position Modular concept Stylish design & high-quality materials Extremely Rugged & Reliable Flexible Communication - AS-I, IO Link and Profinet

Contacts Single piece, formed construction Tin plated Wire seals are crimped individually with the contact AMP DIN 72585 Based on DIN 72585, this range of sealed connectors has been developed to meet the demand for superior performance. Vibration proofed Resistant to physical shock Wide temperature range Single wire sealing system Contact Compatibility Plug/Socket Contact 7 Way 1.5mm 2 to 4 Way 2.5mm Shell Material Glass filled PBT Current Rating 1.5mm 25A 2.5mm 30A Contact Resistance 10mΩ IP Rating IP67 & IP69K Temperature Range -40 to +130°C

Plug-in Reducer - KQG2 Series SMC’s KQG2 stainless steel range provides engineers with a choice of high performance, lightweight, compact push in fittings for when resistance to corrosion, chemicals and high temperatures is vital. 30% smaller and 62% lighter than the existing KQG range and available to tubing diameters from 3.2 to 16mm. Suitable for use with compressed air, water, steam and able to perform across a diverse range of pressure (-100kPa to 1MPa) and temperature conditions (-5°C to +150°C). Threaded, Tube-to-Tube & Adaptors - SMC KQG2 KQG2 SUS316 Stainless Steel Fittings SMC KQG2 series one-touch pneumatic fittings are manufactured from SUS316 stainless steel, offering corrosion resistant properties that are better than grade 304 stainless steel. SUS316 stainless steel offers higher pitting and corrosion resistance properties, and is especially suitable for chloride environments. Applications KQG2 series one-touch fittings make use of FKM seals and may be used with a variety of tubing including nylon, soft nylon, polyurethane, polyolefin, FEP and PFA. The fittings are suitable for use with steam and are grease-free.

AS1803 Neutral Cure Thermally Conductive Silicone RTV These non-corrosive, 1-part, room temperature vulcanising (RTV) silicone rubbers are part of a new family of acetone cure sealants that are solvent free. They are suitable for a wide range of bonding and sealing applications particularly in the electronics industries. They exhibit excellent primerless adhesion to many substrates. The product is cured rapidly in contact with atmospheric moisture to a tough weather and moisture resistant rubber. They will not corrode copper or its alloys and exhibit excellent primerless adhesion when fully cured. Non corrosive Good spreading and tooling properties Fast skinning Good adhesion to most substrates No H&S issues 100% Solids Solvent Free Rheology Self Levelling Colour White Thermal Conductivity 1.55 W/mK Temperature Range -50 to +220°C Tack Free Time 4 mins 3mm Cure Silicone Compounds - ACC

Anti Surge (T) HBC Ceramic Bodied, 5 x 20 Littelfuse Time lag ceramic body cartridge fuses are ideal for applications when surge withstand is required. Breaking capacity 1.5kA @ 250VacApprovals SEMKO,BSI, VDE, CSA, MITI

EMI / RFI braided screen Double-thick metal mesh screens, suited for electromagnetic shielding and weight continuity of assemblies or electric cable harnesses. For effective shielding, both ends must be earthed. Frequency Field Attenuation (dB) 1 MHz Electric 69 10 MHz Electric 62 100 MHz Electric 50 Nominal thickness: 0.4 mm ±0.05

Tray Inserts 47mm inserts suitable for Carrylite 55 mm case, compact toolboxes or plastic drawer cabinets. 69mm inserts suitable for 80mm deep Boxxter and carrylite 80mm case and deep multitray. The inserts sold in multiple quantities will fit a footprint of 320x220mm or 160x 220mm Mixed Inserts Comprise of - 4 x A9-1,2 x A9-2,2 x A8-1,2 x A8-2,2 x A8-3

CONN BASE SIDE ENTRY SZ10B M20

Barrel Pumps Choice of two barrel pumps, designed for use with 40 gallon metal drums, which will pump up to Hypoid 90 viscosity Lever action pump ( RS 672-425 ) incorporates 84cm galvanised steel suction tube, discharge hose optional extra Rotary action pump ( RS 672-419 ) incorporates 96cm steel suction tube and comes with M24 x 4mm retention adaptor

HSS Individual Counterbores Counterbores for cutting holes where a capscrew or fastener is required to sit flush or even below the level of the workpiece. Thread size is the size of the screw thread to sit within the hole and cutting diameter shows the size that will be cut for both the capscrew and head.

DryLin® SHT Basic Fitted with maintenance free DryLin R bearings, this linear slide table can operate at dynamic loads of up to 2000N and static loads of 2800N. Designed for positioning systems and guiding applications, the DryLin module is especially well suited for use in dirty and dusty environments. All-in-one linear system Maintenance free Iglidur W300 trapezoidal leadscrew nut Extremely high load capacity Maximum traverse speed 1m/min All polymer and anodised aluminium lightweight design Dimensions (mm) A A1 H E1 E2 E3 R F W tg sg d T L2 d2 85 -0.3 85 -0.3 34 70 ±0.15 73 ±0.15 73 ±0.15 42 2 30 ±0.1 M8 M6 12 TR10 x 2 17 6 (h9) Load Ratings Max. Axial Load Static (N) 700 Dynamic / MPa x m/s (axial bearing) 0.23 Dynamic / MPa x m/s (trapezoidal nut) 0.08 Max. Radial Load Static (N) 2800 Dynamic (N) 2000 Max. Leadscrew Speed (rpm) 500 Max. Feedrate (m/min) 1

HardCap Aerolite A1+ Underneath the textile cover is a tough HDPE shell and a lightweight EPP impact liner Reflective areas on the side panels of the cover and reflective piping around the peak The cover has large open weaved panels allowing the easy transfer of cool air Replaceable padding Comfort pad and the sweatband are fast drying The cover is removable and machine washable Standards EN812

Screw Cap Choice of release caps Nylon body and cap, UL94-VO rated Low insertion resistance Protection: PC2 Approvals UL Panel Mounting CATEGORIES OF PROTECTION AGAINST ELECTRIC SHOCK,PC1: No integral protection against electric shock. If required, designers must provide additional protection against electric shock on equipment.,PC2: With integral protection against electric shock. Fuse-holders shall have live parts inaccessible to IEC529 standard test finger, when fully assembled, without fuse carrier or fuse in place and when fuse carrier, with fuse is being inserted or withdrawn.,PC3: With integral protection against electric shock. Fuse-holders shall have live parts inaccessible to IEC529 1mm diameter rigid test wire when fully assembled, without fuse carrier or fuse in place and when fuse carrier, with fuse is being inserted or withdrawn.

150-Part Tool Kit, Wave Profile 1/4"; 3/8"; 1/2"150-part socket kit with wave profile and ball lock retainer, in three drive sizesMade of chrome vanadium steelSpecial profile grips the flanks instead of the edges of the screw headsSuitable for Imperial, metric, outer Torx and also worn screw headsNo sliding, even in difficult usage conditionsSupplied in PE hard shell caseIncludes1 x each ratchet handle 72 teeth with square drive:1/4"; 3/8"; 1/2"1 x each universal joint with square drive and output:1/4"; 3/8"; 1/2"1 x extension 1/4" x 100 mm1 x square extension 1/2" x 250 mm and sliding adapter1 x each square extension 1/4" x 50 mm; 3/8" x 125 mm; 1/2" x 125 mm1 x sliding T-handle with 1/4" output1 x each square adapter on hexagon 3/8" x 5/16", 1/2" x 5/16"1 x screwdriver handle with 1/4" square drive and output1 x angled hexagon:1.3; 1.5; 2; 2.5; 3; 4; 5 mmBit inserts1 x each blade, square 1/4":4; 5.5; 6.5; 7 mm, hexagon 5/16": 8; 10; 121 x each PHILLIPS, square 1/4":PH0; PH1; PH2; hexagon 5/16": PH3; PH41 x each POZIDRIV, square 1/4":PZ0; PZ1; PZ2; hexagon 5/16": PZ3; PZ41 x each TORX, square 1/4":T8; T9; T10; T15; T20; T25; T27; T30 and hexagon 5/16": T40; T45; T50; T55; T60; T701 x each TORX-BO, square 1/4":T8H; T9H; T10H; T15H; T20H; T25H; T27H; T30H; hexagon 5/16": T40H; T45H; T50H; T55H; T60H; T70H1 x each Allen, 1/4" square:3; 4; 5; 6; 5/16" hexagon: 7; 8; 10; 12; 14 mmSocket inserts1 x each 1/4" short:4; 4.5; 5; 5.5; 6; 7; 8; 9; 10; 11; 12; 13; 14 mm and long: 4; 5; 6; 7; 8; 9; 10 mm1 x each 3/8" short:10; 11; 12; 13; 14; 15; 16; 17; 18; 19 mm and long: 10; 11; 12; 13; 14; 15 mm1 x each 1/2" short:10; 11; 12; 13; 14; 15; 16; 17; 18; 19; 20; 21; 22; 24; 27; 30; 32 mm and long: 16; 17; 18; 19; 22 mm1 x spark plug connector:3/8" x 18; 1/2" x 16; 1/2" x 21 mm1 x each E-Profile outer TORX,1/4":E4; E5; E6; E7; E8;3/8": E10; E11; E12; E14; E16 and1/...

K10 Industrial Cam Switches Thermal current rating 10A 16 or 22mm diameter fixing hole Operating temperature -20 to +55°C Slow break contacts