Rates
Products Found: 30
Showing Results For: Voltage Indicators
Voltage Indicators
FILTERS
Filters
Showing
1 -
New Items
New items
New items
FLUKE T110/VDE, Fluke
Fluke T90/T110/T130/T150 Voltage and Continuity Testers
All electricians need a two-pole tester. The Fluke T90, T110, T130 and T150 two-pole voltage and continuity testers are rugged and easy- to- use. The designs offer a choice of functionality and user interface. The different models offer combinations of large buttons (convenient for use with gloved hands), bright backlights, clear audible and/or physical indicators (LEDs or vibration).
750-8438 FLUKE-T90 Voltage/Continuity Tester
750-8431 FLUKE-T110 Voltage/Continuity Tester with switchable load, vibration and built-in torch
750-8435 FLUKE-T130 Voltage/Continuity Tester with LCD, switchable load, vibration and built-in torch, display hold
750-8444 FLUKE-T150 Voltage/Continuity Tester with LCD, Ohms, switchable load, vibration and built-in torch, display hold
Features & Benefits
Rugged easy-to-operate two pole AC voltage and continuity testers
Handheld and lightweight
Ergonomic design, feels good in the hand
Unit cases heavy duty moulded
Probe protector
Thick test leads with wear indicators
Operates on 2 x AAA batteries (included)
Protected to IP54 (T90), IP64 (T110, T130, T150)
Dimensions 233 x 65 cm x 38 mm (T90), 260 x 70 x 38 mm (T110, T130, T150)
Weight 180 g (T90), 280 g (T110, T130, T150)
Supplied with
2 x AAA batteries, instruction sheet
Voltage Level Indicators
A range of voltage testers each available in versions suitable for electronic or electrical applications.
New items
9205190000, Weidmuller
Slimline Indicators 6-400V AC/DC
Slimline voltage indication ranges of 6, 50 and 110V.
Volt Check 3
AC/DC voltage check
Automatic range selection
Polarity indication on DC up to 50V
AC indication when both polarity indicators are lit
Bright neon indicator for voltages 110V and above
Tester reduces the test current for high voltages to prolong the LED life
Voltage Surge Proof
5kV/3 joules
Max Operating Period
30 secs
Caution
This unit should be checked for correct operation using a known voltage before use.
Supplied with
Instruction manual.
Voltage Level Indicators
A range of voltage testers each available in versions suitable for electronic or electrical applications.
New items
New items
FLUKE-T150VDE/H15, Fluke
This kit includes the Fluke T150VDE Voltage Indicator and the Fluke H15 holster.
Fluke's family of Two-Pole Voltage Testers are built with state-of-the-art measurement and safety technology, these testers offer everything you expect from Fluke, and a little bit more.
Features and Benefits
The Fluke two-pole testers are now more rugged and easier to use than ever before.
Fast test results the way you need them, with large, easy-to-use buttons, bright backlights, and clear audible and physical indicators designed for any work situation.
Rugged, high-quality construction is built to last. This includes a heavy duty molded case, a thicker cord with wear indicator, sturdy battery case, and well-fitting and durable probe protector.
Enhanced ergonomic design feels good in your hand, is easy to use (even with gloves on) and quick, secure probe docking.
Backlit graduated scale and backlit indicators
Audio on/off for testing in quiet areas.
Low battery indicator
Detects voltage even with discharged batteries
Improved probe docking for secure storage
New items
M630H, Gossen Metrawatt
PROFISAFE 690B Voltage and Continuity Tester
PROFISAFE 690B (M630H) Voltage and Continuity Tester in accordance with DIN EN 61243-3 / VDE 0682-401.
Voltage test
Phase test
Polarity test
Phase sequence indication
Continuity test
Display: 7 steps (bargraph) 12, 24, 50, 120, 230, 400, 690 V
Rugged housing
Protection IP 65
Easy to operate, VDE-GS tested
Measuring category: CAT IV 600 V / CAT III 690 V
Test voltage: 6 kV
Voltage Level Indicators
A range of voltage testers each available in versions suitable for electronic or electrical applications.
New items
VOLT CHECK 3.1-2mm -9205190000, Weidmuller
Slimline Indicators 6-400V AC/DC
Slimline voltage indication ranges of 6, 50 and 110V.
Volt Check 3
AC/DC voltage check
Automatic range selection
Polarity indication on DC up to 50V
AC indication when both polarity indicators are lit
Bright neon indicator for voltages 110V and above
Tester reduces the test current for high voltages to prolong the LED life
Voltage Surge Proof
5kV/3 joules
Max Operating Period
30 secs
Caution
This unit should be checked for correct operation using a known voltage before use.
Supplied with
Instruction manual.
Voltage Level Indicators
A range of voltage testers each available in versions suitable for electronic or electrical applications.
New items
New items
MS917/2, Catu
MS-917/2 Voltage Multi-Tester
The MS-917/2 is a voltage absence tester in accordance with EN 61243-3 (2010) and EN 50110-1 standards. Voltage detector and multi-tester which checks the absence of voltage (AC and DC).
Indicates the voltage level from 12 to 690 Vac or dc
Checks the polarity
Search of phase and neutral
Checks the phase rotation (2 leads method)
Checks the continuity with a pushbutton
IP2X safety probes with retractable shrouded plugs in accordance with NF C 18-510
Frequency : 50 - 60 Hz ± 3%
IP65 / IK06
Class II
In accordance with IEC 61010 (leads plugs)
Category IV - 600V
Dimensions : 165 x 48 x 40 mm
Supplied with
2 x AAA batteries, packaging blister.
Voltage Level Indicators
A range of voltage testers each available in versions suitable for electronic or electrical applications.
New items
CA742, Chauvin Arnoux
Chauvin Arnoux Low-voltage Two-pole Voltage Absence Tester CA742
Chauvin Arnoux CA742 is a voltage detector with indicator lights. It is an instrument of choice for electricians checking that no voltage is present before working on an electrical installation connected to the network. It complies with IEC 61243-3 Edition 2 and can be used to work on any indoor or outdoor 600 V CAT IV installation. To fulfil the requirements of the standards and legislation in different countries, RS offers different versions - without IP2X accessories (
914-0021
) and with IP2X accessories (
914-0025
). The CA742 is equipped with a redundant safety system in the event of power supply faults. An 'ELV LED' flashes whenever the voltage exceeds 50 V AC / 120 V DC. The full Autotest of the CA742 checks the electrical circuits, the power supply, the display and the condition of the measurement leads.
Features and Benefits
Full integrated autotest
Voltage testing up to 690 V AC (16 2/3 Hz - 800 Hz) / 750 V DC
Single-pole phase test
Phase sequence testing up to 400 Hz
Input impedance >300 kΩ
Continuity testing
Removable test probe and cable
Dimensions 163 x 64 x 40 mm
IP65 protection rating
Weight 210 g
Note
The voltages indicated on the CA742 are nominal voltages - users must ensure the device will be used on networks at standardised voltages.
Standards
EN 61243-3 Ed.2009, EN 61243-3 Ed.2010, DIN VDE 0682-401 Ed.2011
Supplied with
Red test probe 2 mm diameter, black lead terminated by test probe 2mm diameter (CA742) or 90 cm black lead and 25 cm red lead terminated
by an IP2X probe tip 4 mm diameter (CA742 IP2X) plus (both models) strap, battery (x2), user manual (in 5 languages), verification certificate
Voltage Level Indicators
A range of voltage testers each available in versions suitable for electronic or electrical applications.
New items
CA742 IP2X, Chauvin Arnoux
Chauvin Arnoux Low-voltage Two-pole Voltage Absence Tester CA742
Chauvin Arnoux CA742 is a voltage detector with indicator lights. It is an instrument of choice for electricians checking that no voltage is present before working on an electrical installation connected to the network. It complies with IEC 61243-3 Edition 2 and can be used to work on any indoor or outdoor 600 V CAT IV installation. To fulfil the requirements of the standards and legislation in different countries, RS offers different versions - without IP2X accessories (
914-0021
) and with IP2X accessories (
914-0025
). The CA742 is equipped with a redundant safety system in the event of power supply faults. An 'ELV LED' flashes whenever the voltage exceeds 50 V AC / 120 V DC. The full Autotest of the CA742 checks the electrical circuits, the power supply, the display and the condition of the measurement leads.
Features and Benefits
Full integrated autotest
Voltage testing up to 690 V AC (16 2/3 Hz - 800 Hz) / 750 V DC
Single-pole phase test
Phase sequence testing up to 400 Hz
Input impedance >300 kΩ
Continuity testing
Removable test probe and cable
Dimensions 163 x 64 x 40 mm
IP65 protection rating
Weight 210 g
Note
The voltages indicated on the CA742 are nominal voltages - users must ensure the device will be used on networks at standardised voltages.
Standards
EN 61243-3 Ed.2009, EN 61243-3 Ed.2010, DIN VDE 0682-401 Ed.2011
Supplied with
Red test probe 2 mm diameter, black lead terminated by test probe 2mm diameter (CA742) or 90 cm black lead and 25 cm red lead terminated
by an IP2X probe tip 4 mm diameter (CA742 IP2X) plus (both models) strap, battery (x2), user manual (in 5 languages), verification certificate
Voltage Level Indicators
A range of voltage testers each available in versions suitable for electronic or electrical applications.
New items
P01191762A, Chauvin Arnoux
Chauvin Arnoux Low-voltage Two-pole Voltage Absence Tester CA762
Chauvin Arnoux CA762 is a voltage detector with indicator lights. It is an instrument of choice for electricians checking that no voltage is present before working on an electrical installation connected to the network. It complies with IEC 61243-3 Edition 2 and can be used to work on any indoor or outdoor 600 V CAT IV installation. To fulfil the requirements of the standards and legislation in different countries, RS offers different versions - without IP2X accessories (
914-0034
) and with IP2X accessories (
914-0037
). The CA762 is equipped with a redundant safety system in the event of power supply faults. An 'ELV LED' flashes whenever the voltage exceeds 50 V AC / 120 V DC. The full Autotest of the CA762 checks the electrical circuits, the power supply, the display and the condition of the measurement leads.
Full integrated autotest
Voltage testing up to 690 V AC (16 2/3 Hz - 800 Hz) / 750 V DC
Single-pole phase test
Phase sequence testing up to 400 Hz
Input impedance >400 kΩ
Continuity testing
Extended continuity test 2 kΩ, 60 kΩ, 300 kΩ
Phase rotation, 2-wire method
Removable test probe and cable
Dimensions 163 x 64 x 40 mm
IP65 protection rating
Weight 210 g
Note
The voltages indicated on the CA762 are nominal voltages - users must ensure the device will be used on networks at standardised voltages.
Supplied with
Red test probe 2 mm diameter, black lead terminated by test probe 2mm diameter (CA742) or 90 cm black lead and 25 cm red lead terminated
by an IP2X probe tip 4 mm diameter (CA742 IP2X) plus (both models) strap, battery (x2), user manual (in 5 languages), verification certificate
Voltage Level Indicators
A range of voltage testers each available in versions suitable for electronic or electrical applications.