Discounted Products

T Series UV Resistant Cable Ties UV resistant cable ties that are recommended for outdoor applications or in areas with high levels of UV exposure. These weatherproof cable ties can be used for routing, bundling and securing of cables, pipes and hoses. Key Features • Weather resistant and UV-resistant • Available in a wide range of sizes • Made from 100% high quality plastic, allows for good recycling • Inside serration for a strong hold onto bundles • Easy application either manually or with a processing tool

CONN FERRULE DIN 10AWG YLW 100PC

Mean Well TS-400 Series 400W True Sine Wave DC-AC Power Inverter TS-400 series 400W true sine wave DC-AC power inverters with digital microprocessor control and high frequency circuit topology enabling a high efficiency of up to 88.5%. These TS-400 series true sine wave DC-AC power inverters are capable of providing 400W continuously for all kinds of harsh load with a low THD of less than 3% peak load capability including 460W for 180 seconds, 600W for 10 seconds or 800W surge power for 30 utility cycles. The output AC voltage and frequency for these DC-AC inverters can be adjusted easily through the front panel. Typical applications for these TS-400 series true sine wave DC-AC power inverters include power tools, office and portable equipment in vehicles, yachts, mobile homes and in other applications where the mains voltage is poor or out of range. True sine wave output (THDHigh efficiency up to 88% High surge power of up to 800W Thermal controlled cooling fan Built-in remote ON-OFF control LED panel indicating operational status Power ON-OFF switch Battery low alarm and battery low shutdown Over voltage, over temperature, output short, input polarity reverse and overload protection EMC compliance to EN55022 class A, 72/ 245/ CEE, 95/ 54/ CE, E-Mark Note Part numbers suffixed with B eg TS-400-212-B have European output plugs Part numbers suffixed with D eg TS-400-212-D have UK output plugs MTBF to MIL-HDBK-217F (25°C) Derate power above 40°C

Vibration Monitor Efector 800 range of Vibration Sensors. Vibration monitor VK Connection via M12 connector Vibration monitor Vrms to DIN ISO 10816 Switching outputs:1 x normally closed DC PNP and 1 x analogue 4 → 20 mA Switching status LED (yellow) Power LED (green) Non latching short circuit protection Overload and reverse polarity protection IP rating: IP67

HOOK-UP STRND 18AWG RED 100'

PMA UNIFLEX CI 45 Temperature Transmitter UNIFLEX CI 45 transmitters are designed to give precise and cost-effective signal detection and processing. Every CI 45 has at least one universal input, one universal output and a relay. Optionally, the transmitter can be fitted with an additional relay, with a second universal input and counter or frequency input. Optionally, the voltage output can also be used as frequency output. Galvanic isolation is provided between inputs and outputs as well as from the supply voltage and the communication interfaces. • Compact design • Display & operating functions • Communication features • High resolution • Fast cycle times • Two universal inputs & universal output • Two relay outputs • Counter/ frequency input, frequency output • Customer-specific linearization • Measurement value correction • Min/max indicator (’slave pointer’) PMA Temperature Transmitters

Progressive Bite Ring Progressive bite rings for use with Ermeto / Parker EO® hydraulic compression fittings and RS Pro hydraulic tube. Banjos, Bite Rings & Tube Nuts Ermeto Original or EO® progressive ring fittings, for metric tube, are manufactured from mild steel, with zinc plated and passivated finish. They are available in light duty and heavy duty series to cover a wide range of pressure ratings. Each fitting comes with a tube nut but the bite ring will need to be ordered separately. The progressive ring bite produces a keyed leak-free tube connection. The range of fittings is intended purely for the assembly of connections for fluid applications. All fittings are supplied with an instruction leaflet. For steel fittings it is recommended that seamless drawn steel tubes to DIN 2391/C are used. Operating temperature range without pressure reductions for the steel fitting material is -40°C to +120°C. Warning Hydraulic systems can work at high pressures. To ensure functional safety of EO® tube fittings, only EO® parts should be used in their assembly and the pressure and temperature ratings should not be exceeded.

True RMS Measurement. Four digit resolution with auto-scaling. Displays Single phase Ampere readings. Field programmable CT primary and secondary.

CBL CLAMP P-TYPE BLACK FASTENER

Type FK Connects round tube parallel to the surface Dimensions (mm) FK 12 FK 18 FK 25 FK 30 FK 40 FK 50 A 12 18 25.1 30.1 40.15 50.2 B 5.3 5.3 6.5 6.5 8.5 10.5 C 18 18 30 30 42 50 D 25 25 40 40 56 66 E 25 25 40 40 60 65 G 35 35 55 55 78 92 H 38 38 53 53 82 98 K 32 32 52 52 71 83 L 38 38 60 60 83 96 M 50 50 78 78 108 128 N 5 5 7 7 10 14 O* n/a n/a n/a n/a 52 62 P 23.5 23.5 33 33 48 58 S M6x25 M6x25 M8x35 M8x35 M10x50 M10x60 Note * FK12 to FK30 have two centrally placed holes, therefore dimension O is not applicable.

Safety Isolating Transformer Safety isolating and isolating control transformers Twin secondary winding for series or parallel connection 63,100,160 and 250VA transformers can be mounted on standard 35mm DIN rail All units have 4 hole panel mount fixings Easy installation 4mm² cage clamp terminals Insulation catagory Class B Primary connections 0V, -15V, +15V, 230V, 400V. The + 15 and -15V allows you to offset the primary Voltage by 15V Low inrush current High efficiency, low regulation Approvals UL Recognised Component for Canada & US Standards EN 61558, VDE0570

CONN INSERT HA16 MALE

MONOCRYSTL SOLAR CELL 111MW 6.3V

SPI-N118/SPP-N118 Flow Meter The SPI-N118 and SPP-N118 flow meters are designed to work together with flow transducers equipped with analogue inputs (SPP-N118) or contact/electronic inputs (SPI-N118). The purpose of the flow meter is to measure the instantaneous flow value and record the total flow of media like liquids, gases or loose materials. The meters are encased in a tight, IP67 rated housing making them suitable for use in harsh environments. The SPI-N118 and SPP-N118 have built-in batcher function allowing the flow meters to be used in many industries such as food, pharmaceutical or paint and varnish. • 6-digit (13 mm) LED display • Flow meter, batcher, totaliser • 1 Pulse counting input & 3 control inputs (SPI-N118) • 1 Input 0/4-20 mA & 1 programmable function input (SPP-N118) • Analogue output: active or passive • RS485/Modbus RTU communication port • Configuration by IR remote controller ( 914-8502 ) or with free S-Config software via RS485 communication port • Display of instantaneous and the total flow values • Batching and counting of doses • Wall mounted, IP67 housing Simex Multi function Meters

RS Pro Plastic Offset Lift Off Hinge The RS Pro off set removable lift off hinges are designed for you to remove your doors without needing tools. The high impact resistant thermoplastic hinges can also be used to mount doors. Features and Benefits Cost effective Quick and easy door removal Simple installation Available in right or left handed

Single Phase Solid State Relays, Celpac Series Celduc range of compact solid state relays with integral heat sink for DIN Rail mounting. Zero voltage switching LED indication DIN Rail mount Dimensions (mm): H 80 x D 112 x W 22.5 (SUL and SILD) H 80 x D 112 x W 45 (SUM) Stock no. Output no. Output Output Switching nominal 409-2968 3.5 → 32 Vdc 150 → 510 Vac 32 A 685-0974 3 → 32 Vdc 12 → 275 Vac 23 A 685-0977 3.5 → 32 Vdc 24 → 510 Vac 32 A 685-0971 150 → 240 Vac / dc 24 → 510 Vac 32 A 685-0980 3.5 → 32 Vdc 24 → 510 Vac 40 A Zero Voltage Relays Note Temperature can affect current rating; please consult the data sheet for potential derating.

EVAL IR38064

RELAY GEN PURPOSE 4PDT 3A 12V

Contactum’s comprehensive range of high quality Ceiling Accessories includes pendants, lampholders, junction boxes and a full range of dry lining and metal boxes. Contactum’s range of Ceiling Accessories includes pendants, lamp holders, junction boxes and a full range of dry lining and metal boxes.

Hellerman Tyton GL Series Cable Ties GalvaLok ties can be used for bundling and fixing. Ideal for use in coastal areas, extreme weather conditions with significant snowfall or areas with high atmospheric concentrations of sulphuric gases. Made from Nylon 66 the resistance is high to these corrosive conditions. Head design minimises insertion force, maximising locking force Smooth strap edges Ideal for bundling cables Wings on bith sides of the head Ideal in environments where steel paneling is used as a building material High resistance to corrosive chemicals

Atomik 215PSS Technologically advanced, injection moulded, heavy duty Polypropylene tool case, which is extremely resistant to chemical corrosion, shock and high and low temperatures. The injection moulding technique ensures constant material thickness, even in the corners. Tools are stored and held in place by the pressure of four rubber blades, these facilitate fast tool change. Ideal for all sizes of tool. 1 lid tool pallet with Flexi-pouches on both sides 1 bottom tool pallet with Flexi-pouches on one side 2 metal locks with keys 2 metal lid safety support stays 3 metal hinges for maximum strength Ergonomic handle, rubber coated grip Document area Base area with removable dividers Address label Can accommodate up to 6 tool pallets Internal dimensions : 465 x 352 x 215mm Weight: 5.5kg Note Case supplied without tools.

MEC Multimec® 5G Series Switches The MEC Multimec® 5G series of tactile switches feature improved cap retention system and actuator over previous Multimec® tactile switches. The MEC Multimec® 5G series is an ideal solution to a wide range of application requirements. 3.5N actuation force Rated for 10 million lifecycles IP67 sealed Switch type: SPNO switch, momentary Switch material: Silver Recommended load: 0.5-50mA, max. 24V Contact resistance: Insulation resistance: >10MΩ Bounce time: Mechanical life: >10,000,000 operations Activation pressure: 2.5 ± 0.2N Key travel: 1mm Temperature range: -40°C to + 65°C - for 3CSH9: -40°C to + 160°C

6060 Series UVC LEDs The 6060 series from LG Innotek is range a UVC LEDs with a peak wavelength of 278 nm. These high power UVC LEDs emit in the "C" area of the UV spectrum and is ideal for use in sterilisation applications. As an ideal alternative to mercury UV LEDs, the 6060 series offers high efficiency, long life-time, a compact package and it is environmentally friendly. It also does not require “warm-up” time in order to begin a sterilisation process. 6060 UVC LEDs come in a square surface mount package with a viewing angle of 120° or 126°. Suitable applications for the 6060 UVC LEDs include; disinfection, water purification, phototherapy, sensor light and counterfeit detection. Features of the 6060 UVC LEDs: 1in1 LED package Surface mounted (SMD) Peak wavelength: 278 nm Low power consumption Low thermal resistance High quality High reliability Dimensions: 6 x 6 x 1.35 mm Operating temperature: -40°C to +60°C Ultraviolet (UV) LEDs, LG

Gaskets Black NBR profiled gaskets Suitable for GDM/GDML/GDME/GDMF sockets Note These connectors are only suitable for power coupling to a fixing point or item of plant, or for internal wiring of equipment. Type A DIN 43650 Hirschmann A comprehensive range of cable sockets, appliance connector bases and accessories typically for use with solenoid valves on pneumatic and hydraulic equipment. The inner connector can be rotated through 90° increments so the gland can be positioned in all four directions. Housing material is glass-filled nylon making them impact resistant.,All Hirschmann appliance connectors feature terminals that can be screwed onto bare or ferruled conductors, or will accept crimp ring/fork terminals under the head of the screw.,All are supplied complete with centre retaining screw, while plug bases are solder terminated and supplied with fixing screws. Suitable gasket to provide IP65 sealing, stock-no. 156-4729. Supplied in bags of 10