Rates
1+
£ 61.45
Products Found: 75
Showing Results For: Mounting Equipment for Air Preparation Components
Mounting Equipment for Air Preparation Components
FILTERS
Filters
Showing
1 -
New Items
New items
1821336007, Aventics
NL Series Mounting Accessories
NL Series FRL
The NL range of air preparation units may be used as single elements or in combination units using joining accessories
New items
FXKE3, Domnick Hunter
Oil-X Evolution Series Filters - General Purpose Grade AO & High Efficiency Grade AA
Meets and exceeds requirements for compressed air quality
Improved air flow management for low energy consumption.
Oil vapour removal
Drainage ribs and no wet band formation
Improved element replacement
Fully corrosion protected
Incident monitor (available separately) to indicate premature high differential pressure. It can be retrofitted to existing housings without depressurising the system.
Fixing clamps (available separately) allow the joining of two filters and act as wall mounting brackets
Technical Specification - Filter units
Max. Operating Pressure
16 bar (232 psi)
Max. Operating Temperature
80°C (176°F)
Min. Operating Temperature
1.5°C (35°F)
Technical Specification - Element Grade AO
High efficiency general purpose protection, particle removal down to 1 micron, including water and oil aerosols. Maximum remaining oil aerosol content: 0.6mg/m3 at 21°C (0.5 ppm(w) at 70°F)
Technical Specification - AA Grade Elements
For high efficiency oil removal/filtration prcede with AO grade filter
Particle removal down to 0.01 microns, including water and oil aerosols
Maximum remaining oil aerosol content: 0.01mg/m
3
or 0.01 ppm(w) at 21°C
Standards
ISO 8573.1
Supplied with
AO or AA grade Filter as appropriate
Key Characteristics
QUALITY
DIRT
WATER
OIL
CLASS
Particle size
Pressure Dewpoint °C
(Including vapour)
in μm
(ppm. vol) at 7 bar g (100 psi g)
mg/m
3
1
0.1
-70 (0.3)
0.01
2
1
-40 (16)
0.1
3
5
-20 (128)
1.0
4
15
+3 (940)
5
5
40
+7 (1240)
25
6
-
+10 (1500)
-
New items
Y410-N03-A, SMC
SMC T-Type Spacer
The cost effective and clean looking AC series from SMC allows you to pick a combination of modular style air preparation equipment that best suits your needs. The series is available in 8 size options to ensure optimum performance offering energy savings with higher flow rates. Simple assembly and maintenance reduces downtime.
Facilitates the redirection of air flow
Easy maintenance
Note
If a T-interface is used on the inlet side of a lubricator that lubricant may be mixed. To avoid this possibility use an AKM series check valve.
New items
E300-F04-A, SMC
Piping Adaptor
Piping adaptors from SMC. This range of piping adaptors are to be used with the AC range of FRL's.
New items
Y40T, SMC
T-Type Bracket/Spacer
T-Type spacer attachments from SMC. Designed to be used with the AC rage of FRL's.
New items
P651AT504958001, Asco
Mounting Accessories
Mounting accessories for use with Asco Numatics 652 and 651 series modular air preparation equipment. This selection of brackets and mounting kits have been designed to for easy installation and maintenance of the 651 and 652 series.
Side Mounting Brackets
A pair of side mounting metal brackets for the mounting of single or multiple air preparation units.
These side mounting brackets are recommended only for static applications.
End Plates with Body-to-Body Assembly Clamp
These endplate kits allow removal of the air preparation assembly for maintenance or replacement without the need for removing any pipework. The kit comes complete with an inlet and outlet plate, sealing O-Rings and two sets of body clamps.
Body-to-Body Assembly Clamp
These body-to-body assembly clamps are easy to assemble with captive screws. O-Ring is included.
Wall/Panel Bracket
The primary mounting feature for the air prep assemblies is the wall/panel bracket. The brackets attach easily to the back of the body-to-body assembly clamps using two screws. In addition, they can be used as a support bracket in between any station on the manifold.
FRL System Accessories
New items
P652AT503860002, Asco
Mounting Accessories
Mounting accessories for use with Asco Numatics 652 and 651 series modular air preparation equipment. This selection of brackets and mounting kits have been designed to for easy installation and maintenance of the 651 and 652 series.
Side Mounting Brackets
A pair of side mounting metal brackets for the mounting of single or multiple air preparation units.
These side mounting brackets are recommended only for static applications.
End Plates with Body-to-Body Assembly Clamp
These endplate kits allow removal of the air preparation assembly for maintenance or replacement without the need for removing any pipework. The kit comes complete with an inlet and outlet plate, sealing O-Rings and two sets of body clamps.
Body-to-Body Assembly Clamp
These body-to-body assembly clamps are easy to assemble with captive screws. O-Ring is included.
Wall/Panel Bracket
The primary mounting feature for the air prep assemblies is the wall/panel bracket. The brackets attach easily to the back of the body-to-body assembly clamps using two screws. In addition, they can be used as a support bracket in between any station on the manifold.
FRL System Accessories
New items
Y20T, SMC
T-Type Bracket/Spacer
T-Type spacer attachments from SMC. Designed to be used with the AC rage of FRL's.
New items
P651AT503860001, Asco
Mounting Accessories
Mounting accessories for use with Asco Numatics 652 and 651 series modular air preparation equipment. This selection of brackets and mounting kits have been designed to for easy installation and maintenance of the 651 and 652 series.
Side Mounting Brackets
A pair of side mounting metal brackets for the mounting of single or multiple air preparation units.
These side mounting brackets are recommended only for static applications.
End Plates with Body-to-Body Assembly Clamp
These endplate kits allow removal of the air preparation assembly for maintenance or replacement without the need for removing any pipework. The kit comes complete with an inlet and outlet plate, sealing O-Rings and two sets of body clamps.
Body-to-Body Assembly Clamp
These body-to-body assembly clamps are easy to assemble with captive screws. O-Ring is included.
Wall/Panel Bracket
The primary mounting feature for the air prep assemblies is the wall/panel bracket. The brackets attach easily to the back of the body-to-body assembly clamps using two screws. In addition, they can be used as a support bracket in between any station on the manifold.
FRL System Accessories
New items
Y21-N01, SMC
SMC T-Type Spacer
The cost effective and clean looking AC series from SMC allows you to pick a combination of modular style air preparation equipment that best suits your needs. The series is available in 8 size options to ensure optimum performance offering energy savings with higher flow rates. Simple assembly and maintenance reduces downtime.
Facilitates the redirection of air flow
Easy maintenance
Note
If a T-interface is used on the inlet side of a lubricator that lubricant may be mixed. To avoid this possibility use an AKM series check valve.
New items
P53801018, SMC
IRV Series Bracket
A series of brackets from SMC, suitable for use with IRV series vacuum regulators.
New items
AR10P-270AS, SMC
AR Series Assemblies
Bracket & panel mount assemblies from SMC are essential accessories for your pneumatic FRL fittings. Available in a variety of sizes within the AR series.