Rates
1+
£ 32.31
Products Found: 1358
Showing Results For: Auxiliary Contacts
Auxiliary Contacts
FILTERS
Filters
Showing
1 -
New Items
New items
417159, Legrand
The Legrand add on auxiliary block used for CTX³ mini contactors. It has a side type mounting with 1 NC contact.
It has a side mounting
New items
276420 | DILA-XHI02, Eaton
Auxiliary contact module, 2 N/C, surface mounting, screw connection
New items
LA1KN11M, Schneider Electric
The Schneider Electric TeSys K instantaneous auxiliary contact block, for contactors LC.K, LP.K (3P + 1NO contact models except LP4K, LP5K) with screw clamp terminals. It provides 1NO+1NC contacts rated up to 10A 690V AC, connection by screw clamp terminals. Marking on terminals conforms to EN 50012.
it procures high reliability and durability for Front mounting by clip-on
New items
LA1KN133, Schneider Electric
Auxiliary Contact Module
Current rating; 10A (Ith)
Front Mounting
Accepts cables up to 2 x 2.5mm
2
One block per contactor, one block per relay
New items
LA1LC025, Schneider Electric
LA1 auxiliary contact blocks
Blocks of instantaneous auxiliary contacts can be added to the right of Integral 63 circuit breaker.
LA1LC010
Block of 6 contacts comprising:
3 contactor status contacts 2 N/O + 1 N/C
1 x 1CO rotating button position status other than "Auto".
1 x 1CO short circuit trip indicator contact
1 x 1CO all-trips indicator contact
LA1LC012
Block of 5 contacts comprising:
3 contactor status contacts 2 N/O + 1 N/C
1 x 1CO short circuit trip indicator contact
1 x 1CO all-trips indicator contact
LA1LC025
Block of 4 contacts comprising:
3 contactor status contacts 2 N/O + 1 N/C
1 x 1 N/O + 1 N/C all-trips indicator contact, to be configured by the user.
Schneider Electric TeSys U
The TeSys U is a modular system for motor control; it enables the user to create a customised solution for their control requirements, from a series of standard modules. The plug-in modules allow the assembly and wiring before the selection of motor protection parameters and control voltages, they can be created or changed in seconds by changing the plug-in modules. A host of DOL starting applications can be catered for.
Faster design with fewer components needed
Quicker panel build with faster assembly time and fewer wires per starter
Space saving 45mm width up to 32A (even for reversing) allowing smaller panels
Flexible and upgradeable with plug-and-play function modules
Voltage and protection parameters can be determined after assembly and wiring
Broad band electronic control unit provides improved overload protection with fewer components
Expandable plug-and–play diagnostics
Total co-ordination for fast return to service after a short circuit fault
Tesys model U is easy to select:
First choose a P...
New items
VZ4, Schneider Electric
Accessories for the Open and Enclosed Switch Disconnectors
Note
Suitable for the 'Vario' range of switch disconnectors
Schneider Electric Vario Range
New items
M5725237, METCASE
METcase Mettec Type B Cases
The Mettec Type B case has an aluminium front and rear bezel, top and base covers and extruded side panels. A high degree of shielding is guaranteed thanks to its masked internal faces and additional contact points. The guide ridges in the side extrusions of the Mettec case allow mounting of PCBs in several positions.
Features and Benefits
Aluminium front and rear bezel, top and base covers and extruded side panels
Front bezel recessed for fitting optional aluminium front panels
Guide ridges in side extrusions for mounting PCBs
All parts fully integrated for strength and shielding
Supplied fully assembled
Fine texture powder polyester finish
Applications
The Mettec Type A case is designed for small desktop and portable electronics equipment. Applications include measuring and control technology, medical, laboratory and peripheral equipment for computers and networking.
Note
Tilt and swivel handles only supplied with stock nos.
209-5858
and
209-5779
.
Supplied with
1 x front bezel, 2 x side extrusions, top and base covers, 1 x rear bezel, 4 non slip feet and fixing screws.
New items
DILM150-XHI13, Eaton
DILM Auxiliary Modules, 4-Pole
These modules plug in to the front of a DILM motor contactor to provide additional contacts
DILM32 auxiliary contacts to be used with DILM9 to DILM32 contactors. DILM150 auxiliary contacts to be used with DILM40 to DILM65 contactors
Current rating 3A (AC 15) @ 400V
New items
S29450, Schneider Electric
PowerPact Auxiliary and Alarm Switches
Range of accessories that provide the circuit breaker contact status
Square D
For use with Qwikline I consumer units and can be retrofitted in to existing systems,Type B characteristic offers instantaneous short circuit response level of 3-5 x normal rated current, making it suitable for circuits with moderate inrush currents such as filament lamps, heating loads and most domestic/small building protection applications.,Type C characteristic offers short circuit response of 5-10 x normal rated current, making it ideal for circuits with higher inrush currents such as motor control and fluorescent lighting installations in industrial buildings where nuisance tripping might occur if a faster type was used
New items
072899 | AGM2-01-PKZ0, Eaton
Eaton Auxiliary Contacts For Use With The PKZ 0 System
A flexible and modular system built for motors up to 4 kW/400 V, the PKZ 0 system offers efficiency whilst being economical whatever the motor started performance profile. Eaton's fail-safe auxiliary contacts offer several contact combinations and are front or right-hand side mountable depending on their design, no tools needed! Trip indication presents through a red short-circuit indicator on some components, allowing users to view a trip easily, other information is provided to the upstream programmable controller. Information provided includes "on/off" on the protective switch, "tripped" message for overload or short circuits, and "on/off" for the contact module.
Features and benefits:
Front and side-mounted contacts available
Easy connection to motor-protective circuit-breakers
Screw terminal connections
On/off switch and module information
For use with PKZM01, PKZM0, PKZM4, PKZM0-T, PKM0, and PKE.
Applications:
Motor starters, Control systems, Control, and Signalling equipment.
How do Auxiliary Contacts work?
An Auxiliary Contact is an electromechanical device that is mounted typically to contactors. They are physically connected to the contactor, with simultaneous activation and deactivation applying to both of the devices at the same time.
Aux Contacts can be installed onto contactors either by front mounting, or side mounting. This is usually clear in the shape and size of the product, but please check the compatibility of your devices. Aux Contacts are really useful devices to aid in keeping an eye on the contactor.
New items
New items
DILM150-XHIA11, Eaton
DILM Auxiliary Modules, 2-Pole
These modules plug in to the front of a DILM motor contactor to provide additional contacts
DILM32 auxiliary contacts to be used with DILM7 to DILM32 contactors. DILM150 auxiliary contacts to be used with DILM40 to DILM150 contactors
Current rating 3A (AC 15) @ 400V