Featured Products
The Melexis magnetic node brings the highest flexibility in the tri axis portfolio's smallest packaged assembly. Additionally the node is designe...
The EVB90632 is an easy interface between the SMD MLX90632 infrared thermometer and a Windows PC. With this PCB one can quickly and easily perfor...
The MLX90109 is a single chip RFID transceiver for the 125kHz frequency range. It has been conceived for minimum system cost and minimum power co...
The MLX90614 is an infrared thermometer for non-contact temperature measurements. Both the IR sensitive thermopile detector chip and the signal c...
The MLX90615 is a miniature infrared thermometer for non-contact temperature measurements. Both the IR sensitive thermopile detector chip and the...
The US1881 is a Hall-effect latch designed in mixed signal CMOS technology that integrates a voltage regulator, Hall sensor with dynamic offset c...
The US5881 is a low sensitive unipolar Hall-effect switch designed in mixed signal CMOS technology.The device integrates a voltage regulator, Hal...
The MLX90614 is an infrared thermometer for non-contact temperature measurements. Both the IR sensitive thermopile detector chip and the signal c...
The MLX90316 is a Triaxis® rotary position sensor IC providing the angular position of a small dipole magnet rotating above the device surface (e...
The MLX90248 is most commonly found in mobile phone applications for detecting the open/close action of the lid (flip, slide and swivel type phon...
The MLX90614 is an infrared thermometer for non-contact temperature measurements. Both the IR sensitive thermopile detector chip and the signal c...
The MLX91205 is a single axis IMC-Hall® integrated current sensor featuring Triaxis® technology. It produces an analog, ratiometric output voltag...
Popular Categories For Melexis
Popular Items
Popular items
MLX90393SLW-ABA-011-RE, Melexis
The Melexis magnetic node brings the highest flexibility in the tri axis portfolio's smallest packaged assembly. Additionally the node is designed for micro power applications with programmable duty cycles in the range of 0.1% to 100% allowing for configurable power consumption based on system requirements. The magnetic field sensor can be reprogrammed to different modes and with different settings at run-time to fine-tune the performance and power consumed.
Simple & robust magnetic design
Miniature size for tiny assemblies
Selectable SPI and I2C bus protocols
Wide dynamic range with on the fly programmable gain
On board filter settings
External and internal acquisition triggering modes
External interrupt pin when the field changes
On board temperature sensor
Popular items
EVB90632, Melexis
The EVB90632 is an easy interface between the SMD MLX90632 infrared thermometer and a Windows PC. With this PCB one can quickly and easily perform a first test of the MLX90632.It also gives access to the internal settings of the sensor to adjust the sensor to a specific application by changing optical window compensation constants, the refresh rate and the I2C address of the sensor.
Comes with two MLX90632 soldered on separate PCBsHID USB interface, Mini-b connectorWindows compatible softwareTest pins to sniff the I²C bus
Popular items
MLX90109EDC-AAA-000-TU, Melexis
The MLX90109 is a single chip RFID transceiver for the 125kHz frequency range. It has been conceived for minimum system cost and minimum power consumption offering all required flexibility for a state of the art AM transceiver base station.An external coil (L) and capacitor (C) are connected as a parallel resonant circuit that determines the carrier frequency and the oscillator frequency of the reader. This eliminates zero modulation effects by perfect antenna tuning, and avoids the need for an external oscillator.The reader IC can easily be switched to power down by setting the antenna amplitude to zero.The MLX90109 can be configured to decode the transponder signal on-chip. In this case the decoded signal is available through a 2-wire interface with clock and data. For minimum interface wiring, the non-decoded transponder signal can also be made available on a single wire interface.
Popular items
MLX90614ESF-ACC-000-TU, Melexis
The MLX90614 is an infrared thermometer for non-contact temperature measurements. Both the IR sensitive thermopile detector chip and the signal conditioning ASIC are integrated in the same TO-39 can. Integrated into the MLX90614 are a low noise amplifier, 17-bit ADC and powerful DSP unit thus achieving high accuracy and resolution of the thermometer.The thermometer comes factory calibrated with a digital SMBus output giving full access to the measured temperature in the complete temperature range(s) with a resolution of 0.02°C.The user can configure the digital output to be pulse width modulation (PWM). As a standard, the 10-bit PWM is configured to continuously transmit the measured temperature in range of -20 to 120°C, with an output resolution of 0.14°C.
Popular items
MLX90615SSG-DAG-000-TU, Melexis
The MLX90615 is a miniature infrared thermometer for non-contact temperature measurements. Both the IR sensitive thermopile detector chip and the signal conditioning ASIC are integrated in the same miniature TO-46 can.With its small size, this infrared thermometer is especially suited for medical applications like ear or forehead thermometers or other applications where "small things make a big difference".The infrared thermometer comes factory calibrated with a digital SMBus output giving full access to the measured temperature in the complete temperature range(s) with a resolution of 0.02 °C. The sensor achieves an accuracy of ±0.2°C within the relevant medical temperature range. The user can choose to configure the digital output to be PWM.
Popular items
US1881LUA-AAA-000-BU, Melexis
The US1881 is a Hall-effect latch designed in mixed signal CMOS technology that integrates a voltage regulator, Hall sensor with dynamic offset cancellation system, Schmitt trigger and an open-drain output driver, all in a single package.Thanks to its wide operating voltage range and extended choice of temperature range, it is quite suitable for use in automotive, industrial and consumer applications.The US1881 has been proved its use into the industry by its widely usage in different markets.The device is delivered in a TSOT for surface mount process and in a Plastic Single In Line (TO-92 flat) for through-hole mount.
Wide operating voltage range from 3.5 V to 24 VHigh magnetic sensitivity – Multi-purposeCMOS technologyChopper-stabilized amplifier stageLow current consumptionOpen drain outputThin SOT23 3L and flat TO-92 3L both packagesSE package North Pole activeUA package South Pole active
Popular items
US5881ESE-AAA-000-RE, Melexis
The US5881 is a low sensitive unipolar Hall-effect switch designed in mixed signal CMOS technology.The device integrates a voltage regulator, Hall sensor with dynamic offset cancellation system, Schmitt trigger and an open-drain output driver, all in a single package.Thanks to its wide operating voltage range and extended choice of temperature range, it is suitable for use in automotive and solid state switch applications.The device is delivered in a TSOT for surface mount process and in a Plastic Single In Line (TO-92 flat) for through-hole mount.
Wide operating voltage range from 3.5 V to 24 VLow sensitivityCMOS technologyChopper-stabilized amplifier stageLow current consumptionOpen drain outputThin SOT23 3L and flat TO-92 3L both packagesSE package North pole activeUA package South pole active
Popular items
MLX90614ESF-ACF-000-TU, Melexis
The MLX90614 is an infrared thermometer for non-contact temperature measurements. Both the IR sensitive thermopile detector chip and the signal conditioning ASIC are integrated in the same TO-39 can. Integrated into the MLX90614 are a low noise amplifier, 17-bit ADC and powerful DSP unit thus achieving high accuracy and resolution of the thermometer.The thermometer comes factory calibrated with a digital SMBus output giving full access to the measured temperature in the complete temperature range(s) with a resolution of 0.02°C.The user can configure the digital output to be pulse width modulation (PWM). As a standard, the 10-bit PWM is configured to continuously transmit the measured temperature in range of -20 to 120°C, with an output resolution of 0.14°C.
Popular items
MLX90316KDC-BCG-000-RE, Melexis
The MLX90316 is a Triaxis® rotary position sensor IC providing the angular position of a small dipole magnet rotating above the device surface (end-of-shaft magnet). Thanks to an IMC on its surface, the monolithic device senses, in a contactless fashion, the horizontal component of the applied magnetic flux density.
This unique sensing principle applied to a rotary position sensor results into an impressive robustness of the angular position over the mechanical (air-gap, off-axis) tolerances. The rotation of this horizontal component is sensed over a wide range (up to 360º) and processed by the on-chip DSP to ultimately report the absolute angular position of the magnet either as a ratiometric analogue output or as Pulse-Width Modulation (PWM) signal or as a 14-bit data accessible through a 3-pin SPI (serial interface) channel.
The output transfer characteristic is fully programmable (e.g. offset, gain, clamping levels, linearity, thermal drift, filtering, range, ...) to match any specific requirement through end-of-line calibration.
Popular items
MLX90248ESE-EBA-000-RE, Melexis
The MLX90248 is most commonly found in mobile phone applications for detecting the open/close action of the lid (flip, slide and swivel type phones) and also to detect the (un)holstered condition of brick and smartphones. The goal of this detection is to switch on or off the power hungry displays, backlights and keypad illumination whenever the lid is opened or closed. Thereby maximizing battery life between charges.The same operation principle can be simply applied to many other battery-powered devices like laptops, digital cameras and camcorders, music players and handheld gaming devices.This very high sensitivity Hall sensor IC allows the use of only a very small and cheap magnet to trigger the MLX90248, hence it can easily replace a reed switch.Several benefits derive from using a Hall sensor IC. One is to provide solid state switching, which is bounce-free, more reliable and with increased lifetime compared to usual mechanical contacts. The other is seamless pick and place manufacturing as the device is available in standard, lead-free and green surface mount technology.
Popular items
MLX90614ESF-AAA-000-TU, Melexis
The MLX90614 is an infrared thermometer for non-contact temperature measurements. Both the IR sensitive thermopile detector chip and the signal conditioning ASIC are integrated in the same TO-39 can. Integrated into the MLX90614 are a low noise amplifier, 17-bit ADC and powerful DSP unit thus achieving high accuracy and resolution of the thermometer.The thermometer comes factory calibrated with a digital SMBus output giving full access to the measured temperature in the complete temperature range(s) with a resolution of 0.02°C.The user can configure the digital output to be pulse width modulation (PWM). As a standard, the 10-bit PWM is configured to continuously transmit the measured temperature in range of -20 to 120°C, with an output resolution of 0.14°C.
Popular items
MLX91205KDC-AAL-003-TU, Melexis
The MLX91205 is a single axis IMC-Hall® integrated current sensor featuring Triaxis® technology. It produces an analog, ratiometric output voltages proportional to the applied magnetic field parallel with the chip surface.The circuit is fabricated using a standard CMOS process, with the addition of an integrated magnetic concentrator (IMC-Hall®). This ferromagnetic layer amplifies the magnetic field and concentrates it on the Hall elements. Therefore, the circuit features very high magnetic sensitivity, low offset and low noise.The MLX91205 is ideally suited for current sensing in automotive and industrial environments. Two different versions with different magnetic ranges are available.
New Items
New items
MLX90393SLW-ABA-011-RE, Melexis
The Melexis magnetic node brings the highest flexibility in the tri axis portfolio's smallest packaged assembly. Additionally the node is designed for micro power applications with programmable duty cycles in the range of 0.1% to 100% allowing for configurable power consumption based on system requirements. The magnetic field sensor can be reprogrammed to different modes and with different settings at run-time to fine-tune the performance and power consumed.
Simple & robust magnetic design
Miniature size for tiny assemblies
Selectable SPI and I2C bus protocols
Wide dynamic range with on the fly programmable gain
On board filter settings
External and internal acquisition triggering modes
External interrupt pin when the field changes
On board temperature sensor
New items
EVB90632, Melexis
The EVB90632 is an easy interface between the SMD MLX90632 infrared thermometer and a Windows PC. With this PCB one can quickly and easily perform a first test of the MLX90632.It also gives access to the internal settings of the sensor to adjust the sensor to a specific application by changing optical window compensation constants, the refresh rate and the I2C address of the sensor.
Comes with two MLX90632 soldered on separate PCBsHID USB interface, Mini-b connectorWindows compatible softwareTest pins to sniff the I²C bus
New items
MLX90109EDC-AAA-000-TU, Melexis
The MLX90109 is a single chip RFID transceiver for the 125kHz frequency range. It has been conceived for minimum system cost and minimum power consumption offering all required flexibility for a state of the art AM transceiver base station.An external coil (L) and capacitor (C) are connected as a parallel resonant circuit that determines the carrier frequency and the oscillator frequency of the reader. This eliminates zero modulation effects by perfect antenna tuning, and avoids the need for an external oscillator.The reader IC can easily be switched to power down by setting the antenna amplitude to zero.The MLX90109 can be configured to decode the transponder signal on-chip. In this case the decoded signal is available through a 2-wire interface with clock and data. For minimum interface wiring, the non-decoded transponder signal can also be made available on a single wire interface.
New items
MLX90614ESF-ACC-000-TU, Melexis
The MLX90614 is an infrared thermometer for non-contact temperature measurements. Both the IR sensitive thermopile detector chip and the signal conditioning ASIC are integrated in the same TO-39 can. Integrated into the MLX90614 are a low noise amplifier, 17-bit ADC and powerful DSP unit thus achieving high accuracy and resolution of the thermometer.The thermometer comes factory calibrated with a digital SMBus output giving full access to the measured temperature in the complete temperature range(s) with a resolution of 0.02°C.The user can configure the digital output to be pulse width modulation (PWM). As a standard, the 10-bit PWM is configured to continuously transmit the measured temperature in range of -20 to 120°C, with an output resolution of 0.14°C.
New items
MLX90615SSG-DAG-000-TU, Melexis
The MLX90615 is a miniature infrared thermometer for non-contact temperature measurements. Both the IR sensitive thermopile detector chip and the signal conditioning ASIC are integrated in the same miniature TO-46 can.With its small size, this infrared thermometer is especially suited for medical applications like ear or forehead thermometers or other applications where "small things make a big difference".The infrared thermometer comes factory calibrated with a digital SMBus output giving full access to the measured temperature in the complete temperature range(s) with a resolution of 0.02 °C. The sensor achieves an accuracy of ±0.2°C within the relevant medical temperature range. The user can choose to configure the digital output to be PWM.
New items
US1881LUA-AAA-000-BU, Melexis
The US1881 is a Hall-effect latch designed in mixed signal CMOS technology that integrates a voltage regulator, Hall sensor with dynamic offset cancellation system, Schmitt trigger and an open-drain output driver, all in a single package.Thanks to its wide operating voltage range and extended choice of temperature range, it is quite suitable for use in automotive, industrial and consumer applications.The US1881 has been proved its use into the industry by its widely usage in different markets.The device is delivered in a TSOT for surface mount process and in a Plastic Single In Line (TO-92 flat) for through-hole mount.
Wide operating voltage range from 3.5 V to 24 VHigh magnetic sensitivity – Multi-purposeCMOS technologyChopper-stabilized amplifier stageLow current consumptionOpen drain outputThin SOT23 3L and flat TO-92 3L both packagesSE package North Pole activeUA package South Pole active
New items
US5881ESE-AAA-000-RE, Melexis
The US5881 is a low sensitive unipolar Hall-effect switch designed in mixed signal CMOS technology.The device integrates a voltage regulator, Hall sensor with dynamic offset cancellation system, Schmitt trigger and an open-drain output driver, all in a single package.Thanks to its wide operating voltage range and extended choice of temperature range, it is suitable for use in automotive and solid state switch applications.The device is delivered in a TSOT for surface mount process and in a Plastic Single In Line (TO-92 flat) for through-hole mount.
Wide operating voltage range from 3.5 V to 24 VLow sensitivityCMOS technologyChopper-stabilized amplifier stageLow current consumptionOpen drain outputThin SOT23 3L and flat TO-92 3L both packagesSE package North pole activeUA package South pole active
New items
MLX90614ESF-ACF-000-TU, Melexis
The MLX90614 is an infrared thermometer for non-contact temperature measurements. Both the IR sensitive thermopile detector chip and the signal conditioning ASIC are integrated in the same TO-39 can. Integrated into the MLX90614 are a low noise amplifier, 17-bit ADC and powerful DSP unit thus achieving high accuracy and resolution of the thermometer.The thermometer comes factory calibrated with a digital SMBus output giving full access to the measured temperature in the complete temperature range(s) with a resolution of 0.02°C.The user can configure the digital output to be pulse width modulation (PWM). As a standard, the 10-bit PWM is configured to continuously transmit the measured temperature in range of -20 to 120°C, with an output resolution of 0.14°C.
New items
MLX90316KDC-BCG-000-RE, Melexis
The MLX90316 is a Triaxis® rotary position sensor IC providing the angular position of a small dipole magnet rotating above the device surface (end-of-shaft magnet). Thanks to an IMC on its surface, the monolithic device senses, in a contactless fashion, the horizontal component of the applied magnetic flux density.
This unique sensing principle applied to a rotary position sensor results into an impressive robustness of the angular position over the mechanical (air-gap, off-axis) tolerances. The rotation of this horizontal component is sensed over a wide range (up to 360º) and processed by the on-chip DSP to ultimately report the absolute angular position of the magnet either as a ratiometric analogue output or as Pulse-Width Modulation (PWM) signal or as a 14-bit data accessible through a 3-pin SPI (serial interface) channel.
The output transfer characteristic is fully programmable (e.g. offset, gain, clamping levels, linearity, thermal drift, filtering, range, ...) to match any specific requirement through end-of-line calibration.
New items
MLX90248ESE-EBA-000-RE, Melexis
The MLX90248 is most commonly found in mobile phone applications for detecting the open/close action of the lid (flip, slide and swivel type phones) and also to detect the (un)holstered condition of brick and smartphones. The goal of this detection is to switch on or off the power hungry displays, backlights and keypad illumination whenever the lid is opened or closed. Thereby maximizing battery life between charges.The same operation principle can be simply applied to many other battery-powered devices like laptops, digital cameras and camcorders, music players and handheld gaming devices.This very high sensitivity Hall sensor IC allows the use of only a very small and cheap magnet to trigger the MLX90248, hence it can easily replace a reed switch.Several benefits derive from using a Hall sensor IC. One is to provide solid state switching, which is bounce-free, more reliable and with increased lifetime compared to usual mechanical contacts. The other is seamless pick and place manufacturing as the device is available in standard, lead-free and green surface mount technology.
New items
MLX90614ESF-AAA-000-TU, Melexis
The MLX90614 is an infrared thermometer for non-contact temperature measurements. Both the IR sensitive thermopile detector chip and the signal conditioning ASIC are integrated in the same TO-39 can. Integrated into the MLX90614 are a low noise amplifier, 17-bit ADC and powerful DSP unit thus achieving high accuracy and resolution of the thermometer.The thermometer comes factory calibrated with a digital SMBus output giving full access to the measured temperature in the complete temperature range(s) with a resolution of 0.02°C.The user can configure the digital output to be pulse width modulation (PWM). As a standard, the 10-bit PWM is configured to continuously transmit the measured temperature in range of -20 to 120°C, with an output resolution of 0.14°C.
New items
MLX91205KDC-AAL-003-TU, Melexis
The MLX91205 is a single axis IMC-Hall® integrated current sensor featuring Triaxis® technology. It produces an analog, ratiometric output voltages proportional to the applied magnetic field parallel with the chip surface.The circuit is fabricated using a standard CMOS process, with the addition of an integrated magnetic concentrator (IMC-Hall®). This ferromagnetic layer amplifies the magnetic field and concentrates it on the Hall elements. Therefore, the circuit features very high magnetic sensitivity, low offset and low noise.The MLX91205 is ideally suited for current sensing in automotive and industrial environments. Two different versions with different magnetic ranges are available.
Don’t hesitate to ask questions for better clarification.