Featured Products
PCB Preparation Seno Chemical Applicators Three applicators each containing safe, ready-to-use PCB chemistry, which...
Microtrak FR4 epoxy glass laminates are dip coated with a high resolution positive working Photoresist. The Photoresist contains a dye which give...
Microtrak FR4 epoxy glass laminates are dip coated with a high resolution positive working Photoresist. The Photoresist contains a dye which give...
12in. Shears Powerful, cost effective, shears which have the ability to accurately cut PCB laminates, plast...
PCB Preparation Seno Chemical Applicators Three applicators each containing safe, ready-to-use PCB chemistry, which offers a clean and efficient...
1/8 in. Shank Tungsten Carbide Drills High grade solid carbide PCB drills, drills remain sharp for much lon...
PCB Preparation Fine Etch Crystals An effective alternative to Ferric Chloride, this etchant eliminates the staining and mess caused by traditio...
The 18" "Raptor" Shear is both powerful and rigid. It can be used on any bench or mounted using the four corner fixing points. Designed and manuf...
Artwork Light Boxes 5mm thick opal Perspex™ diffuser panel Working surface is completely flush Non-slip rubber feet...
Replacement UV Tubes & Starters for UV Exposure Units These kits contain 2 tubes and 2 starters for use as...
1/8 in. Shank Tungsten Carbide Drills High grade solid carbide PCB drills, drills remain sharp for much lon...
Popular Categories For Mega Electronics
Popular Items
Popular items
600-006, Mega Electronics
PCB Preparation Seno Chemical Applicators
Three applicators each containing safe, ready-to-use PCB chemistry, which offers a clean and efficient alternative to processing in trays
Each applicator is sealed with a valve mechanism terminated by a sponge which dispenses precisely the right amount on the board
All applicators work at room temperature, are waste free, and when exhausted can be disposed of without any special precautions
363-6517
SN110 (Universal Developer):
Applicator which
develops
all alkaline positive working resists. Contains 50ml of developer sufficient to process approximately 40 standard Eurocards (100 x 160mm)
363-6523
SN120 (Resist Strip):
Applicator which quickly removes
(strips)
all remaining
Photoresist
from etched boards. Contains 80ml of resist-strip sufficient to process approximately 30 standard Eurocards (100 x 160mm)
363-6539
SN140 (Flux):
Applicator which applies a protective lacquer to a clean etched circuit, preventing any further oxidation. Lacquer also acts as an excellent solder
flux
. Contains approximately 80ml of flux sufficient to process aproximately 70 standard Eurocards (100 x 160mm)
Processing Chemicals
Suitable for use with the RS PCB tanks, these processing chemicals are supplied conveniently packaged to make up sufficient working solution for one tank fill. Instructions for the use of these chemicals are printed on the package, and are repeated in the instruction leaflet supplied with all tanks in the range.
Popular items
03-5153-1, Mega Electronics
Microtrak FR4 epoxy glass laminates are dip coated with a high resolution positive working Photoresist. The Photoresist contains a dye which gives a good contrast against the copper, allowing boards to be easily inspected at the developing stage. Panels are protected by a specially designed light-proof blue film which allows panels to be guillotined without the risk of fracturing the Photoresist.
Popular items
Popular items
03-5151, Mega Electronics
Microtrak FR4 epoxy glass laminates are dip coated with a high resolution positive working Photoresist. The Photoresist contains a dye which gives a good contrast against the copper, allowing boards to be easily inspected at the developing stage. Panels are protected by a specially designed light-proof blue film which allows panels to be guillotined without the risk of fracturing the Photoresist.
Popular items
700-500, Mega Electronics
12in. Shears
Powerful, cost effective, shears which have the ability to accurately cut PCB laminates, plastics up to 2.0mm thick and aluminium up to 1.5mm thick.
An important feature of these shears is safety.
Free access to the cutting area is prevented by heavy Perspex shielding along both sides of the blade.
A safety latch is fitted to the pivot to prevent operation without it first being released.
For positional accuracy the cutting bed is fitted with a rule, which is recessed, to assist in securing the PCB or sheeting whilst cutting is in progress.
The 12in. shears will cut materials up to 305mm (12in.) and has a height of 670mm and a footprint of 440mm x 245mm. It has a larger cutting bed 225mm from the blade although once again wider material can be cut.
Dimensions (mm): W 570 x H 180 x D 290
Weight: 8kg
PCB Assembly Equipment
Popular items
600-004, Mega Electronics
PCB Preparation Seno Chemical Applicators
Three applicators each containing safe, ready-to-use PCB chemistry, which offers a clean and efficient alternative to processing in trays
Each applicator is sealed with a valve mechanism terminated by a sponge which dispenses precisely the right amount on the board
All applicators work at room temperature, are waste free, and when exhausted can be disposed of without any special precautions
363-6517
SN110 (Universal Developer):
Applicator which
develops
all alkaline positive working resists. Contains 50ml of developer sufficient to process approximately 40 standard Eurocards (100 x 160mm)
363-6523
SN120 (Resist Strip):
Applicator which quickly removes
(strips)
all remaining
Photoresist
from etched boards. Contains 80ml of resist-strip sufficient to process approximately 30 standard Eurocards (100 x 160mm)
363-6539
SN140 (Flux):
Applicator which applies a protective lacquer to a clean etched circuit, preventing any further oxidation. Lacquer also acts as an excellent solder
flux
. Contains approximately 80ml of flux sufficient to process aproximately 70 standard Eurocards (100 x 160mm)
Processing Chemicals
Suitable for use with the RS PCB tanks, these processing chemicals are supplied conveniently packaged to make up sufficient working solution for one tank fill. Instructions for the use of these chemicals are printed on the package, and are repeated in the instruction leaflet supplied with all tanks in the range.
Popular items
13-111015-1, Mega Electronics
1/8 in. Shank Tungsten Carbide Drills
High grade solid carbide PCB drills, drills remain sharp for much longer than standard steel drills when drilling epoxy glass PCB laminates. A high speed is recomended to produce good quality holes and avoid breakage. These drill bits are fitted with drill collars for ease of use and identification.
PCB Drilling / Milling tools
Popular items
600-014, Mega Electronics
PCB Preparation Fine Etch Crystals
An effective alternative to Ferric Chloride, this etchant eliminates the staining and mess caused by traditional etchants
The mixed solution remains odourless and any splashes or drips can be wiped away with a damp cloth, preventing staining
6-8 minute etching times at 50°C should be expected with fresh solution
4-6 week life expected in tank (can be increased by adding a little more powder to exhausted solution)
Supplied in 1kg powder bag sufficient to make 5 litres of etching solution
Based on a Sodium Persulphate and Stabiliser formula
Processing Chemicals
Suitable for use with the RS PCB tanks, these processing chemicals are supplied conveniently packaged to make up sufficient working solution for one tank fill. Instructions for the use of these chemicals are printed on the package, and are repeated in the instruction leaflet supplied with all tanks in the range.
Warning
This is a hazardous product. It may intensify fire. It is harmful if swallowed. It can cause: serious eye irritation; allergy or asthma symptoms or breathing difficulties if inhaled; an allergic skin reaction.
Popular items
700-800, Mega Electronics
The 18" "Raptor" Shear is both powerful and rigid. It can be used on any bench or mounted using the four corner fixing points. Designed and manufactured in the UK the Shear which has the ability to accurately cut PCB laminates, Plastics up to 2.00mm thick and Aluminium up to 1.5mm along the whole cutting length of 18" (457mm). The bottom blade is reversible providing two cutting edges. An important feature of this shears is safety. Free access to the cutting area is prevented by heavy Perspex shielding extending along both sides of the blade. These guards are split allowing easy alignment of materials. A safety latch is fitted to the pivot to prevent operation without it first being released. A 12" (305mm) wide cutting bed is fitted although wide material can also be cut. For positional accuracy the bed is fitted with a metric and imperial scale to aid accurate cutting.
Popular items
RS_462-8343, Mega Electronics
Artwork Light Boxes
5mm thick opal Perspex™ diffuser panel
Working surface is completely flush
Non-slip rubber feet fitted
Can be tilted up to 60°
Supply Voltage
240Vac 50Hz
Fluorescent Tubes:
2 x Daylight (cool white)
Small Unit
8W
Large Unit
20W
Viewing Area:
Small Unit
300 x 300mm
Large Unit
610 x 458mm
Correlated colour temperature
Approx. 4300°K
Popular items
170012&172016, Mega Electronics
Replacement UV Tubes & Starters for UV Exposure Units
These kits contain 2 tubes and 2 starters for use as replacements in UV exposure units.
Note
The kits are not physically or electrically interchangeable.
Popular items
13-111017-1, Mega Electronics
1/8 in. Shank Tungsten Carbide Drills
High grade solid carbide PCB drills, drills remain sharp for much longer than standard steel drills when drilling epoxy glass PCB laminates. A high speed is recomended to produce good quality holes and avoid breakage. These drill bits are fitted with drill collars for ease of use and identification.
PCB Drilling / Milling tools
New Items
New items
600-006, Mega Electronics
PCB Preparation Seno Chemical Applicators
Three applicators each containing safe, ready-to-use PCB chemistry, which offers a clean and efficient alternative to processing in trays
Each applicator is sealed with a valve mechanism terminated by a sponge which dispenses precisely the right amount on the board
All applicators work at room temperature, are waste free, and when exhausted can be disposed of without any special precautions
363-6517
SN110 (Universal Developer):
Applicator which
develops
all alkaline positive working resists. Contains 50ml of developer sufficient to process approximately 40 standard Eurocards (100 x 160mm)
363-6523
SN120 (Resist Strip):
Applicator which quickly removes
(strips)
all remaining
Photoresist
from etched boards. Contains 80ml of resist-strip sufficient to process approximately 30 standard Eurocards (100 x 160mm)
363-6539
SN140 (Flux):
Applicator which applies a protective lacquer to a clean etched circuit, preventing any further oxidation. Lacquer also acts as an excellent solder
flux
. Contains approximately 80ml of flux sufficient to process aproximately 70 standard Eurocards (100 x 160mm)
Processing Chemicals
Suitable for use with the RS PCB tanks, these processing chemicals are supplied conveniently packaged to make up sufficient working solution for one tank fill. Instructions for the use of these chemicals are printed on the package, and are repeated in the instruction leaflet supplied with all tanks in the range.
New items
03-5153-1, Mega Electronics
Microtrak FR4 epoxy glass laminates are dip coated with a high resolution positive working Photoresist. The Photoresist contains a dye which gives a good contrast against the copper, allowing boards to be easily inspected at the developing stage. Panels are protected by a specially designed light-proof blue film which allows panels to be guillotined without the risk of fracturing the Photoresist.
New items
New items
03-5151, Mega Electronics
Microtrak FR4 epoxy glass laminates are dip coated with a high resolution positive working Photoresist. The Photoresist contains a dye which gives a good contrast against the copper, allowing boards to be easily inspected at the developing stage. Panels are protected by a specially designed light-proof blue film which allows panels to be guillotined without the risk of fracturing the Photoresist.
New items
700-500, Mega Electronics
12in. Shears
Powerful, cost effective, shears which have the ability to accurately cut PCB laminates, plastics up to 2.0mm thick and aluminium up to 1.5mm thick.
An important feature of these shears is safety.
Free access to the cutting area is prevented by heavy Perspex shielding along both sides of the blade.
A safety latch is fitted to the pivot to prevent operation without it first being released.
For positional accuracy the cutting bed is fitted with a rule, which is recessed, to assist in securing the PCB or sheeting whilst cutting is in progress.
The 12in. shears will cut materials up to 305mm (12in.) and has a height of 670mm and a footprint of 440mm x 245mm. It has a larger cutting bed 225mm from the blade although once again wider material can be cut.
Dimensions (mm): W 570 x H 180 x D 290
Weight: 8kg
PCB Assembly Equipment
New items
600-004, Mega Electronics
PCB Preparation Seno Chemical Applicators
Three applicators each containing safe, ready-to-use PCB chemistry, which offers a clean and efficient alternative to processing in trays
Each applicator is sealed with a valve mechanism terminated by a sponge which dispenses precisely the right amount on the board
All applicators work at room temperature, are waste free, and when exhausted can be disposed of without any special precautions
363-6517
SN110 (Universal Developer):
Applicator which
develops
all alkaline positive working resists. Contains 50ml of developer sufficient to process approximately 40 standard Eurocards (100 x 160mm)
363-6523
SN120 (Resist Strip):
Applicator which quickly removes
(strips)
all remaining
Photoresist
from etched boards. Contains 80ml of resist-strip sufficient to process approximately 30 standard Eurocards (100 x 160mm)
363-6539
SN140 (Flux):
Applicator which applies a protective lacquer to a clean etched circuit, preventing any further oxidation. Lacquer also acts as an excellent solder
flux
. Contains approximately 80ml of flux sufficient to process aproximately 70 standard Eurocards (100 x 160mm)
Processing Chemicals
Suitable for use with the RS PCB tanks, these processing chemicals are supplied conveniently packaged to make up sufficient working solution for one tank fill. Instructions for the use of these chemicals are printed on the package, and are repeated in the instruction leaflet supplied with all tanks in the range.
New items
13-111015-1, Mega Electronics
1/8 in. Shank Tungsten Carbide Drills
High grade solid carbide PCB drills, drills remain sharp for much longer than standard steel drills when drilling epoxy glass PCB laminates. A high speed is recomended to produce good quality holes and avoid breakage. These drill bits are fitted with drill collars for ease of use and identification.
PCB Drilling / Milling tools
New items
600-014, Mega Electronics
PCB Preparation Fine Etch Crystals
An effective alternative to Ferric Chloride, this etchant eliminates the staining and mess caused by traditional etchants
The mixed solution remains odourless and any splashes or drips can be wiped away with a damp cloth, preventing staining
6-8 minute etching times at 50°C should be expected with fresh solution
4-6 week life expected in tank (can be increased by adding a little more powder to exhausted solution)
Supplied in 1kg powder bag sufficient to make 5 litres of etching solution
Based on a Sodium Persulphate and Stabiliser formula
Processing Chemicals
Suitable for use with the RS PCB tanks, these processing chemicals are supplied conveniently packaged to make up sufficient working solution for one tank fill. Instructions for the use of these chemicals are printed on the package, and are repeated in the instruction leaflet supplied with all tanks in the range.
Warning
This is a hazardous product. It may intensify fire. It is harmful if swallowed. It can cause: serious eye irritation; allergy or asthma symptoms or breathing difficulties if inhaled; an allergic skin reaction.
New items
700-800, Mega Electronics
The 18" "Raptor" Shear is both powerful and rigid. It can be used on any bench or mounted using the four corner fixing points. Designed and manufactured in the UK the Shear which has the ability to accurately cut PCB laminates, Plastics up to 2.00mm thick and Aluminium up to 1.5mm along the whole cutting length of 18" (457mm). The bottom blade is reversible providing two cutting edges. An important feature of this shears is safety. Free access to the cutting area is prevented by heavy Perspex shielding extending along both sides of the blade. These guards are split allowing easy alignment of materials. A safety latch is fitted to the pivot to prevent operation without it first being released. A 12" (305mm) wide cutting bed is fitted although wide material can also be cut. For positional accuracy the bed is fitted with a metric and imperial scale to aid accurate cutting.
New items
RS_462-8343, Mega Electronics
Artwork Light Boxes
5mm thick opal Perspex™ diffuser panel
Working surface is completely flush
Non-slip rubber feet fitted
Can be tilted up to 60°
Supply Voltage
240Vac 50Hz
Fluorescent Tubes:
2 x Daylight (cool white)
Small Unit
8W
Large Unit
20W
Viewing Area:
Small Unit
300 x 300mm
Large Unit
610 x 458mm
Correlated colour temperature
Approx. 4300°K
New items
170012&172016, Mega Electronics
Replacement UV Tubes & Starters for UV Exposure Units
These kits contain 2 tubes and 2 starters for use as replacements in UV exposure units.
Note
The kits are not physically or electrically interchangeable.
New items
13-111017-1, Mega Electronics
1/8 in. Shank Tungsten Carbide Drills
High grade solid carbide PCB drills, drills remain sharp for much longer than standard steel drills when drilling epoxy glass PCB laminates. A high speed is recomended to produce good quality holes and avoid breakage. These drill bits are fitted with drill collars for ease of use and identification.
PCB Drilling / Milling tools
Don’t hesitate to ask questions for better clarification.