Oscilloscope Kits

Diagnostic Accessories Kit for Red Pitaya STEMLab Red Pitaya diagnostic accessories kit consisting of the following: 2 x osciloscope probes 2 x SMA to BCN adapters 2 x 50 ohm terminations 2 x SMA T adapters WIFI dongle Red Pitaya PC Based Instruments

The Metrix oscilloscope kit features a circuit which generates 15 varied and representative signals, along with a guide that describes the nature of each signal, the METRIX oscilloscope model used to perform the test and the correct calibrations for the equipment to obtain optimal visualisation. It has two channels available via BNC connection: MAIN and AUX It can be powered by a standard 9V battery

Teledyne LeCroy High Definition Oscilloscopes

Picoscope 4444 Standard High Resolution Differential Oscilloscope Kit The PICOSCOPE 4444 STANDARD KIT from Pico Technology is a high-resolution differential USB oscilloscope with three PicoConnect 441 1:1 passive differential voltage probes and one TA271 single-ended D9-BNC adaptor. The PicoScope 4444 uses specially designed passive voltage probes that have smaller and lighter (or no) interface boxes makes multiple differential measurements at the same time while never occupying more than one power socket. It's intelligent probe interface automatically configures the PicoScope display to probes. The four D9 inputs allow to make true differential measurements. The 12bit resolution of the PicoScope 4444 offers 16 times as much vertical detail and its deeper capture memory of 256MS gives it greater horizontal resolution. It is used in non-ground-referenced measurements, safe probing of single phase and 3-phase voltages and currents, measuring power drawn by mobile and IoT devices, hybrid and electric vehicle design, motor drives and inverters. Features and Benefits FFT spectrum analyzer, high resolution offers 64x more detail Hardware acceleration engine (HAL3), 100000 waveforms per second Maximum input range at full scale is ±50V (±1000V using the PicoConnect 442 1000V CAT III probe) Maximum common-mode range is also ±50V (also ±1000V with the PicoConnect 442 probe) Interface for intelligent probes and clamps, 4 fully differential high impedance inputs Low voltage probe for millivolts to 50V and 20MHz bandwidth 1000V CAT III probe for high voltage applications Waveform buffer and navigator Pico PC Based Instruments

Picoscope 4444 CAT III High Resolution Differential Oscilloscope Kit The PICOSCOPE 4444 1000 V CAT III KIT from Pico Technology is a high-resolution differential oscilloscope with three PicoConnect 442 1000V CAT III passive differential voltage probes and one TA271 single-ended D9-BNC adaptor. The PicoScope 4444 uses specially designed passive voltage probes that have smaller and lighter (or no) interface boxes makes multiple differential measurements at the same time while never occupying more than one power socket. It's intelligent probe interface automatically configures the PicoScope display to probes. The four D9 inputs allow to make true differential measurements. The 12bit resolution of the PicoScope 4444 offers 16 times as much vertical detail and its deeper capture memory of 256MS gives it greater horizontal resolution. It is used in non-ground-referenced measurements, safe probing of single phase and 3-phase voltages and currents, measuring power drawn by mobile and IoT devices, hybrid and electric vehicle design, motor drives and inverters. Deep-memory oscilloscopes (256MS deep memory), waveform buffer and navigator Hardware acceleration engine (HAL3), 100000 waveforms per second Maximum input range at full scale is ±50V (±1000V using the PicoConnect 442 1000V CAT III probe) Maximum common-mode range is also ±50V (also ±1000V with the PicoConnect 442 probe) Low voltage probe for millivolts to 50V and 20MHz bandwidth 1000V CAT III probe for high voltage applications Rejects common mode noise, signal integrity, digital triggers Waveform buffer and navigator Pico PC Based Instruments