Cable Tracers & Fuse Finders

UNITEST Wire Detector Set Detection of wires in the wall, open circuits, short circuits in wires Detection of fuses and assignment to circuits Detection of accidentally plastered sockets and distribution boxes Set consisting of transmitter and receiver in impact-resistant, robust storage case Transmitter signal indicated optically and acoustically Clear, understandable instruction manual with application examples Additional transmitters are available for the extension or differentiation of several signals All application areas (whether volt free or under voltage) are covered without any additional devices Reliable localisation thanks to indicator showing defined letter on the receiver Location depth: 0 → 40 cm Electric strength: 250 V Fouling factor: 2 Overvoltage category CAT II / 250 V to earth Safety in accordance with: EN 61010-1/IEC 61010 1x9 V, IEC 6LR61 receiver, Power source: 2x9 V, IEC 6LR61 transmitter Supplied with 1 unit. UNITEST cable protector receiver, 1 unit. UNITEST cable protector transmitter code 'F', 3 units. 9 V battery, IEC 6LR61, 2 units. Crocodile clips red/black, 1 unit. Instruction Manual

Elite Fuse Finder Martindale FD550 This microprocessor-controlled instrument quickly and accurately identifies which fuse or circuit breaker protects which circuit, avoiding accidentally isolating the wrong circuit LED bargraph signal strength indicator Automatic mode - automatic sensitivity adjustment with memory for reliable circuit identification Manual mode - manual adjustment for rapid fuse finding Non-contact voltage indicator to show presence of voltages from 40 to 600Vac Single person operation Supplied with 13A plug in transmitter, Elite receiver & instructions. Requires 1 off MN1604/PP3 alkaline battery (stock No. 463-0712 ) Supplied with 13A plug in transmitter, Elite receiver & instructions rugged hard carry case, TL83 leads with crocodile clips, 13A mains adaptor.

MADE NADIR LV Cable Tracer NADIR enables the identification of a live low voltage cable and the ID of each phase under load in a trench and at the substation exit. Nadir consists of a transmitter and a receiver and is used on a low voltage powered network with or without loads. The transmitter is connected between phases (preferred connection) or between phase and neutral downstream of the measuring point on a low voltage network. Using the receiver, the cable between the transmitter and the medium / low voltage distribution substation can be identified. As can the connection of the feeder in the substation. NADIR also enables identification of the three conductors in the low voltage feeder.

CATV Cable Tone Test Set 402k Each kit consists of: one transmitter, one receiver, one male F-to-F connector adapter cable, one male F-to-alligator clip adapter cable, and a 700C carrying case. Designed specifically for the CATV industry, the Model 402K will send tone through any passive device along the cable path. Now you can tone through splitters, directional couplers and traps. No more long delays trying to figure out non-tagged or mis-tagged cable drops. The Model 402K is simple to use and provides fast, accurate results. The transmitter and receiver are equipped with female F connectors and the kit provides both audible and LED test and tone indications. The addition of optional adapter test leads allows the 402K to be used on distribution cables as well as wire pairs or single conductors Tone through splitters Identify non tagged cable drops Identify mis-tagged cable drops Fast, Accurate Cable Identification Sends Tone to Identify Wires Four Distinct Tone Signatures Simple to use Adjustable Volume Control Visual and Signal Strength Indication Large Speaker for Noisy Environments Rugged Industrial Design Requires 2 x 9V PP3 batteries (stock no. 448-8511 )

PTS100/200 - Pair Tracing Kit The PTS Pair Tracing System comprises the PTS 200 Tone Generator and the PTS 100 Probe in a woven polyester carrying pouch. The System is designed to provide an easy to use and cost effective means of tracing wire pairs Fast, Accurate Wire Identification Sends Tone to Identify Wires Polarity Indication Continuity Test Adjustable Volume Control Easy to Operate 2-Line Modular Test Lead Rugged Industrial design Water Resistant Typical Applications: PTS 200 Tone Generator: The PTS 200 may be connected via the modular plug or the crocodile clips to the pair under test. Depending on the switch position the Tone Generator will test Polarity continuity or short circuits. The PTS 200 can be used on twisted pair wiring (Telecom, Datacom, security / alarm, audio and electrical), single conductors, coaxial cables, de-energized AC wiring and just about any other wiring you can think of. PTS 100 Probe: The PTS 100 Probe has a built-in loudspeaker to make it easy to hear the tracing signals and a near/far sensitivity Adjustment to allow both broad searches and pinpoint identification of wires. To operate just press the button on the top and adjust the sensitivity control to hear the tone generated by the PTS 200 Note Only for use on non-powered cables, powered by PP3 batteries (not supplied). Image for illustration purposes only

CD1000 Cable Detector Kit The Martindale CD1000 Cable Detector is ideal for tracing cables in walls and underground, locating fuses/breakers on live or dead circuits and locating interruptions and open-circuits in cables and electrical floor heating systems. It can also be used for tracing metallic water and heating pipes. For all applications (live or dead cables) without additional instruments Proven digitally coded sender signal guarantees clear signal identification Transmitter with LCD display for transmitting level, transmitting code Receiver with a backlight LCD display for level of receiving signal, code of receiving signal and live voltage indication Automatic or manual adjustment of receiving signal sensitivity Mute function Auto power off Additional torch lamp for working in dark environments Additional transmitters can be used for multiple users Conforms to BS EN61010-1 CAT III 300V Class II Double Insulation Pollution degree: 2 Transmitter: Conforms to BS EN 61010-1 CAT III 600V Class II Double Insulation Pollution degree: 2 Receiver: Supplied with Transmitter, Receiver, bag, TL47 test leads (with crocodile clips), earthing rod, 9V alkaline battery, 1.5V alkaline battery x 6 and instructions