The PAN1740 is a short-range BLE single mode module used for the implementation of Bluetooth functionality into various electronic devices.
Pre-programmed BT/MAC address
Includes 16 MHz and 32 768 kHz crystal
calibrated up to 1 ppm
Single-mode Bluetooth Smart System-on-Chip
Programmable ARM CORTEX M0 CPU
Autonomous BTLE stand-alone operation
Bluetooth v4.1 (LE) embedded GATT profile –
Low Energy single mode
Small 9.0 mm x 9.5 mm x 1.8 mm SMD package
with antenna
Less than a few μA in low power modes
Integrated shielding to resist EMI
No external components needed
Peak power consumption 4.9 mA Rx and Tx
Link budget 93 dBm (Rx sensitivity -93, Tx 0 dBm)
Operating temperature range -40 °C to +85 °C
MRF24J40MC, 2.4GHz Transceiver Module
The MRF24J40MC is a 2.4 GHz IEEE Std. 802.15.4™ compliant, surface mount module with integrated crystal, internal voltage regulator, matching circuitry, Power Amplifier (PA), Low Noise Amplifier (LNA) and with a 50Ω external antenna connector.
The MRF24J40MC module is compatible with Microchips ZigBee®, and MiWi™ Development Environment software stacks. The MiWi Development Environment software stack including the source code is available as a free download, from the Microchip web site.
IEEE Std. 802.15.4™ Compliant RF Transceiver
Supports ZigBee®, MiWi™ Development Environment Proprietary Wireless Networking Protocols
4-Wire Serial Peripheral Interface (SPI) with Interrupt
Small size: 22.9 x 33 mm (0.9 x 1.3 in.), Surface Mountable
Integrated Crystal, Internal Voltage Regulator, Matching Circuitry, Power Amplifier, Low Noise Amplifier
External Antenna Connector : Ultra Miniature Coaxial (U.FL), 50Ω
Easy Integration into Final Product : Minimize Product Development, Quicker Time to Market
Radio Regulation Certified for United States (FCC), Canada (IC), Europe (ETSI) and Australia/New Zealand (C-TICK)
Compatible with Microchip microcontroller families (PIC16, PIC18, PIC24, dsPIC33 and PIC32)
Range up to 1200m (4000 feet)
WPAN (IEEE 802.15.4) - Microchip
The BDK-GEVK, featuring RSL10, industry's lowest power Bluetooth 5 SoC, serves as a baseboard for the Bluetooth IoT Development Kit (B-IDK). Daughter cards or shields compatible with B-IDK can be connected to the baseboard either via the PMOD connectors or the Arduino style connector. Multiple sensor and actuator daughter cards can be connected to the BDK-GEVK board to expand its functionality and enable the development of various IoT use cases.Connecting higher power actuator daughter cards to BDK-GEVK will require the BDK-DCDC-GEVB board
chiliboard M2M (4G) Sandwich
chiliboard M2M (4G) Sandwich by Grinn is based on the 4G Telit module (with GSM and GPS modem) and is suitable for use with chiliboard and liteboard.
Features
Based on 4G Telit module LE910-EUG
Bands: UMTS 850/900/2100 (EU), LTE FDD (3, 7, 20) (EU)
MicroSIM holder
SMA Female connectors for antennas
Operating temperature range (C): -40 to 85
Grinn
RN-52 Bluetooth 3.0 Audio Evaluation Board
The Microchip RN-52-EK-1 is an evaluation board for the RN52 Bluetooth Version 3.0 Audio Module, allowing designers to easily evaluate and develop the RN52 into Bluetooth audio applications. The RN52 is fully compatible with Version 2.1+EDR and supports Bluetooth profiles A2DP, AVRCP, HFP/HSP, SPP and iAP.
Features
RN52 Bluetooth Module
Dual channel audio output and input available in analogue and digital formats
USB port for power supply and command interface
Built-in stereo audio amplifier
Support for codecs such as aptX®, AAC, MP3, and others
Package Contents
RN52 Evaluation Board
USB Cable
Note
Speakers and Microphone are not included. A complete kit including these items is available; Microchip part RN-52-EK.
Bluetooth - Microchip
This xCHIP, the RFM95W transceiver features the LoRaTM long range modem that provides ultra-long range, spread spectrum communication and interference immunity whilst minimizing current consumption.
This xCHIP, the RFM95W transceiver features the LoRaTM long range modem that provides ultra-long range, spread spectrum communication and interference immunity whilst minimizing current consumption.
Product highlights
915 MHz LoRa Radio
LoRaTM Modem
Fully Static Operation
Software Programmable Frequency and Modes
+23 dBm Transmit Power
-148 dBm Sensitivity
USB to UART Development Module with Battery Charger Support, FTDI Chip
The UMFT231XC is a USB to UART development module with battery charging support.
Configured with a LTC4053EDD lithium-ion battery charger
Charging a battery of a device via USB slave port, with either 1 Ampere of current from a dedicated charger port or with up to 500mA from a USB host, without violating USB compliance regulations
3-way 3.5mm screw terminal for connecting a battery to the module
Thermal regulation safety feature
10-pin 0.1 female header used for UART signals, 12 pin 0.1 female header for Power and control
Status LEDs
Mini USB-B connector
Power MOSFET for suspending power supplied to an external circuit from USB bus when in USB suspend mode
The FTDI Chip UMFT234XD is a breakout board that converts USB2.0 Full-Speed to UART. These modules do not have a USB connector, instead, the modules plug directly into the USB host connector and the pads of the PCB makes electrical contact with the electrical contacts of the USB connector. The UART interface operates at +3.3V voltage levels, however all I/Os are 5V tolerant.
USB to UART with four control bus lines, 33V power out limited to 50mA and 5V with as safety fuse
UART signals available via 8 pads on the PCB
CETA FORM VDE Insulated Combination Pliers 180mm
VDE 0682 Part 201, DIN ISO 5746
VDE approved - tested to 10000V AC
Ideal for live working up to 1000V AC or 1500V DC
Suitable for cutting soft and hard wire
Special tool steel
Chrome finish
DuoTech softgrip handles
CETA FORM 1000V Single-Pole Voltage Tester (VDE Approved-Long)
VDE Approved - tested to 10000V AC
178mm Long
VDE 0680/06, DIN 57680/6, TS 13108
For 110 to 250V
Silicon Chrome Vanadium steel blade (nickel finish)
TNK-11 = Version
Housing: Aluminium,
Sea Water Resistance
Temp.Range: -80...+150 °C
Max.Pressure: 16 Bar
Probe Material: Brass
Protection: IP65
05 = Probe Length: 50 mm
D5 = Process connection: Thread Rotatable M18 x 1.5
1 = Sensor Model: Class B 1 x Pt100
2 = Sensor Version: 2 Wire
P = Cable clamp: 5-10 mm Diameter
Y2441 = Special Feature: Grey Housing
CETA FORM Insulated 160mm Long Nose Pliers (VDE Approved)
VDE 0682 Teil 201, DIN ISO 5745
Ideal for live working up to 1000V AC or 1500V DC
Suitable for cutting soft and hard wire
Special tool steel
Chrome finish
DuoTech softgrip handles
VDE Approved for live working up to 1000V AC or 1500V DC. Tested to 10,000V AC. Chrome Vanadium Molybdenum steel blade (phosphate finish). C-PLUS Soft-Grip handle. Individually tested as per DIN EN 60900: 2004 norm. 7 Piece Kit contains:
3.0 x 100 mm C-PLUS Insulated Slotted Screwdriver (VDE Approved) x 1
4.0 x 100 mm C-PLUS Insulated Slotted Screwdriver (VDE Approved) x 1
5.5 x 125 mm C-PLUS Insulated Slotted Screwdriver (VDE Approved) x 1
6.5 x 150 mm C-PLUS Insulated Slotted Screwdriver (VDE Approved) x 1
PZ1 x 80 mm C-PLUS Insulated Pozidriv Screwdriver (VDE Approved) x 1
PZ2 x 100 mm C-PLUS Insulated Pozidriv Screwdriver (VDE Approved) x 1
Single-Pole Voltage Tester (VDE Approved-Long) x 1
G20-18-0160 Insulated Wire Stripping Pliers (VDE Approved)VDE 0682Tested to 10000VIdeal for live working up to 1000V AC or 1500V DCFor stripping the plastic insulation of single and multi-strand conductor special tool steel chrome finishDuoTech soft grip handlesVDE 0682 Teil 201Ideal for live working up to 1000V AC or 1500V DCFor stripping the plastic insulation of single and multi-strand conductorsSpecial tool steelChrome finishDuoTech softgrip handles
G12 Series Insulated Diagonal Cutter (VDE Approved)
VDE 0682 part 201, DIN ISO 5749
Ideal for live working up to 1000V AC or 1500V DC
Suitable for cutting soft and hard wire
Special tool steel
Chrome finish
DuoTech softgrip handles
CETA FORM RZR Series Insulated Cable Shear 170mm (VDE Approved)
Ideal for live working up to 1000V AC or 1500V DC
Cutting capacity: Ø 15 mm
For cutting copper and aluminum cables
Special tool steel
Phosphate finish
DuoTech softgrip handles
Not suitable for steel wire and wire rope
CETA FORM 1000V Insulated Water Pump Pliers 250mm (VDE approved)
VDE 0682 part 201, DIN ISO 8976
VDE approved - tested to 10000V AC
Ideal for live working up to 1000V AC or 1500V DC
9-position adjustment
Chrome Vanadium steel
Phosphate finish
Softgrip handles
We offer free shipping for orders over £200 if delivery is in the UK. All other orders in the UK, shipping from £7.99 depending on the weight and measurement. Mainland Europe shipping charges start from £25. For all other countries shipping charges start from £50 for products like Communication & Wireless Development Tools and all others.
You can email us directly at sales@enrgtech.co.uk or via our website for any queries regarding Communication & Wireless Development Tools or any other product.
This depends on the Communication & Wireless Development Tools individual product and information that can be found on our website.
Yes, we offer special discounts on orders above £200 for Communication & Wireless Development Tools and all other products.
UK orders normally take between 2/3 working days. International orders normally take between 3/5 working days for all products including Communication & Wireless Development Tools.
Yes. We keep updating our stock frequently and if a product like Communication & Wireless Development Tools is not in stock then we will let you know.