Products Found: 7
Showing Results For: Plastic Pipe Cement
Plastic Pipe Cement
FILTERS
Filters
Enrgtech #
Manufacturer Part No
Description
Availability
Rating
RS Pro
Plumbing can be used for bonding non- pressure, thermoplastic pipe systems such as U-PVC BS EN 1329 and ABS BS EN 1455. Provides excellent adhesion and sealing action even where there are gaps between the surfaces to be bonded (up to 0.8mm). Store in a shaded and well ventilated area below 44°C. Use within 2 years of date stamped on bottom of can.
Cut pipe square. Mark pipe OD equal to socket depth.
Aggressively clean joining surfaces with WELD-ON cleaner.
Apply cement to pipe. Apply cement to fitting. Apply again to pipe.
Insert pipe fully into fitting while cement is still wet. Wipe off excess cement. Hold together for 10 sec.
Do not move joint for 10 minutes. Check cure time schedule.
Check Stock & Lead Times Packaging Options
Georg Fischer
Tangit ABS Solvent Cement
Solvent cement for the joining of PVC and ABS pipes. Ideal for use in pressure applications as the bond is very flexible, resistant to heat and waterproof. Suitable for gas/water piping and electrical conduits.
Recommended for joining ABS pipe and fittings by creating a chemical bond
Thixotropic, does not drip
No abrasion required
Joints can be made at ambient temperatures as low as -5°C
Tangit cleaning fluid is recommended for preparation of the joint surfaces and for cleaning cement residue from brushes
Warning
Flammable
Check Stock & Lead Times Packaging Options
RS Pro
Use only on PVC and CPVC plastic. Read WELD-ON® Installation Guide, Product Bulletin and SDS.
Cut pipe square and deburr. Clean and dry joining surfaces.
Check dry fit. Fitting should go over end of pipe easily but become tight about 1/3 to 2/3 of the way on.
Use a suitable applicator at least 1/2 the size of pipe diameter, for larger sizes use a swab or roller. Do not use a rag as repeated contact with skin may cause irritation or blistering.
Apply primer to inside of fitting equal to socket depth, without delay coat pipe end up to socket depth until soft. Apply again to fitting socket. Avoid puddling.
On bell end pipe, do not coat or allow primer to run beyond socket depth.
To check penetration, scratch surface. Re-coat if necessary. Actual time for priming action is affected by pipe diameter and temperature.
Immediately while surfaces are still wet, apply appropriate WELD-ON® cement following directions on cement can.
Check Stock & Lead Times Packaging Options
Georg Fischer
Tangit PVC-U Solvent Cement
Tangit is a gap filling solvent cement for jointing PVC-U pipe and fittings, by creating a chemical bond. Joints made with TANGIT remain unaffected by almost all fluids for which PVC-U pipe is suitable. However, prolonged exposure of the inside joint edge to any of the following acid concentrations can cause some deterioration of the cement bonding.
Sulphuric acid over 70%
Hydrochloric acid over 25%
Nitric acid over 20%
Hydrofluoric acid in all concentrations
Features and Benefits
Provides a tensile and stable connection
Fire protection
Application Information
For the connection of pipes made of PVC-U, PVC-C and ABS.
Note
A PVC-U cleaning fluid is recommended for preparation of the joint surface and for cleaning cement residue from brushes
Standards
In accordance with BS4346: Part 3
Warning
Flammable
Check Stock & Lead Times Packaging Options
RS PRO
RS PRO Plastic Pipe Cement
Features and Benefits
How to apply plastic pipe cement
How to store pipe cement
Can you remove plastic pipe cement?
Check Stock & Lead Times Packaging Options
RS PRO
RS PRO Plastic Pipe Cement
Features and Benefits
How to apply plastic pipe cement
How to store pipe cement
Can you remove plastic pipe cement?
Check Stock & Lead Times Packaging Options
Georg Fischer
Tangit Cleaner
Tangit PVC-U/PVC-C/ABS cleaner that has been specially developed for cleaning solvent jointed plastics.
Specially developed for cleaning solvent jointed plastics, PVC-U, PVC-C and ABS
Pepper pot top to avoid wastage and reduce evaporation
1 litre bottle
Warning
Flammable
Check Stock & Lead Times Packaging Options
New Added Items
Added items
Tangit ABS Solvent Cement
Solvent cement for the joining of PVC and ABS pipes. Ideal for use in pressure applications as the bond is very flexible, resistant to heat and waterproof. Suitable for gas/water piping and electrical conduits.
Recommended for joining ABS pipe and fittings by creating a chemical bond
Thixotropic, does not drip
No abrasion required
Joints can be made at ambient temperatures as low as -5°C
Tangit cleaning fluid is recommended for preparation of the joint surfaces and for cleaning cement residue from brushes
Warning
Flammable
Added items
Plumbing can be used for bonding non- pressure, thermoplastic pipe systems such as U-PVC BS EN 1329 and ABS BS EN 1455. Provides excellent adhesion and sealing action even where there are gaps between the surfaces to be bonded (up to 0.8mm). Store in a shaded and well ventilated area below 44°C. Use within 2 years of date stamped on bottom of can.
Cut pipe square. Mark pipe OD equal to socket depth.
Aggressively clean joining surfaces with WELD-ON cleaner.
Apply cement to pipe. Apply cement to fitting. Apply again to pipe.
Insert pipe fully into fitting while cement is still wet. Wipe off excess cement. Hold together for 10 sec.
Do not move joint for 10 minutes. Check cure time schedule.
Added items
Use only on PVC and CPVC plastic. Read WELD-ON® Installation Guide, Product Bulletin and SDS.
Cut pipe square and deburr. Clean and dry joining surfaces.
Check dry fit. Fitting should go over end of pipe easily but become tight about 1/3 to 2/3 of the way on.
Use a suitable applicator at least 1/2 the size of pipe diameter, for larger sizes use a swab or roller. Do not use a rag as repeated contact with skin may cause irritation or blistering.
Apply primer to inside of fitting equal to socket depth, without delay coat pipe end up to socket depth until soft. Apply again to fitting socket. Avoid puddling.
On bell end pipe, do not coat or allow primer to run beyond socket depth.
To check penetration, scratch surface. Re-coat if necessary. Actual time for priming action is affected by pipe diameter and temperature.
Immediately while surfaces are still wet, apply appropriate WELD-ON® cement following directions on cement can.
Added items
Tangit PVC-U Solvent Cement
Tangit is a gap filling solvent cement for jointing PVC-U pipe and fittings, by creating a chemical bond. Joints made with TANGIT remain unaffected by almost all fluids for which PVC-U pipe is suitable. However, prolonged exposure of the inside joint edge to any of the following acid concentrations can cause some deterioration of the cement bonding.
Sulphuric acid over 70%
Hydrochloric acid over 25%
Nitric acid over 20%
Hydrofluoric acid in all concentrations
Features and Benefits
Provides a tensile and stable connection
Fire protection
Application Information
For the connection of pipes made of PVC-U, PVC-C and ABS.
Note
A PVC-U cleaning fluid is recommended for preparation of the joint surface and for cleaning cement residue from brushes
Standards
In accordance with BS4346: Part 3
Warning
Flammable
Added items
RS PRO Plastic Pipe Cement
Features and Benefits
How to apply plastic pipe cement
How to store pipe cement
Can you remove plastic pipe cement?
Added items
RS PRO Plastic Pipe Cement
Features and Benefits
How to apply plastic pipe cement
How to store pipe cement
Can you remove plastic pipe cement?
Added items
Tangit Cleaner
Tangit PVC-U/PVC-C/ABS cleaner that has been specially developed for cleaning solvent jointed plastics.
Specially developed for cleaning solvent jointed plastics, PVC-U, PVC-C and ABS
Pepper pot top to avoid wastage and reduce evaporation
1 litre bottle
Warning
Flammable
